background image

51396c GB/2019-04

21 / 27

1

 electronic GmbH & Co. KG  •  Heinrichstraße 3-4  •  12207 Berlin  •  Deutschland  •  [email protected]

Maintenance and repair  

6.1 Maintenance 

 

The ultrasonic bath requires no maintenance.
For purposes of regular control, the following functional checks may be carried out.

6.2  

Functional checks  

Checking control lights

A test routine can be started for an internal function check:
To do so, the ultrasonic bath must be switched off. When the Start/Stop button is 
pressed and held, the ultrasonic bath is switched on with the ON/OFF button. 
All LEDs light up successively for 1/3 of a second. The last set values are then 
displayed. 
The test is then successfully completed.
If there are any deviations, the ultrasonic bath must be sent in for checking/repairs.

Checking the ultrasound and/or heating

The function can be tested using a standard wattmeter. It is to be inserted between the 
ultrasonic bath's power plug and the power outlet. 
•  Fill the oscillating tank up to the lower 

fi

 lling level mark with 

fl

 uid, see chapter 4.2.

•  For testing purposes, only the ultrasound or only the heating system needs to be 

plugged in. Then, the value displayed should be compared with the corresponding 
value in the technical data (chapter 1.4) (tolerances ± 20%). 

Summary of Contents for SONOREX PR 140




























Reviews: