background image

There is no temperature setting button 
or temperature scale on ultrasonic baths 
without heating (PR 140 D).  

ultrasonic bath ON/OFF button

temperature setting button with temperature scale above

time setting button with time scale above

Start/Stop button – ultrasound

1

2

3

4

12 / 27

51396c GB/2019-04

1

 electronic GmbH & Co. KG  •  Heinrichstraße 3-4  •  12207 Berlin  •  Deutschland  •  [email protected]

3 Operation 

 

3.1  

Operating elements  

The ultrasonic bath is controlled from the front:

3.1.1  

Ultrasound  

With the ultrasonic bath turned on – ON/OFF button – the time is 
preset, then the ultrasound output is turned on with the Start/Stop 
button.

Timed operation

•  It is set by pressing buttons  

  Time 1, 2, 3, 4, 5, 10, 15 or 30 minutes

-  After pressing the Start/Stop button, a running light displays the remaining time 

optically.  

-  Once the time expires, the ultrasonic output is stopped automatically.  

•  Premature pressing of the Start/Stop button ends the ultrasound output.

Continuous operation

•  It is set by pressing buttons 

  LED  

 lights up

-  After pressing the Start/Stop button, the top (green) LED lights up continuously.  
-  The ultrasonic bath does not turn off automatically: press the Start/Stop button 

to switch it off. 

Remarks

•  For safety reasons, the ultrasound bath is turned off automatically if no button is 

pressed for more than 12 hours.

•  While turned off, the ultrasonic bath may remain connected to the mains. 

It can be disconnected from the mains by pulling the mains plug.

Summary of Contents for SONOREX PR 140




























Reviews: