background image

3

PanelMax

 installation instructions

WARNING!

•  The door may operate unexpectedly, therefore do not allow anything to stay in the path 

of the door.

•  When operating the manual release while the door is open, the door may fall rapidly 

due to weak or broken springs, or due to being improperly balanced. 

•  The drive must not be used with a door incorporating a wicket door, unless the drive 

cannot be operated with the wicket door open. 

•  The drive is intended to be installed at least 2.5m above the floor.
•  Do not disengage the opener to manual operation with children/persons or any objects 

including motor vehicles within the doorway.

•  If the door is closing and is unable to re-open when obstructed, discontinue use. Do not 

use a door with faulty obstruction sensing

•  When using auto close mode, a Photo Electric beam must be fitted correctly and tested 

for operation at regular intervals.  Extreme caution is recommended when using auto 
close mode.  All safety rules must be followed.

 

ELECTROCUTION!

•  Place opener in protected area so that it does not get wet.
•  Do not spray with water .
•  Disconnect the power cord from mains power before making any repairs or removing 

covers. Only experienced service personnel should remove covers from the opener.

•  If the power supply cord is damaged, it must be replaced by an Automatic Technology 

service agent or suitably qualified person.

•  Connect the opener to a properly earthed general purpose 240V mains power outlet 

installed by a qualified electrical contractor.

CAUTION:

Emergency Access

•  If garage has no pedestrian entrance door, an emergency access device should  be 

installed. This accessory allows manual operation of the garage door from outside in 
case of power failure.

Muscular strain

•  Practice correct lifting techniques (carton weighs approx 5.7kgs)
•  Practice correct lifiting techniques when required to lift the door as per installation instructions.

Fall from ladder

•  Ensure ladder is the correct type for job.
•  Ensure ladder is on flat firm ground that will take the weight without the legs sinking.
•  Ensure user has 3 points of contact while on ladder.

Crush injury from 
unsecured door

•  Place a 2 metre exclusion zone around area under the door while it is unsecured.
•  Follow the installation instructions

Garage Door

•  Examine the door installation, in particular, springs and mountings for signs of wear, damage 

and imbalance.

•  The garage door must be well balanced. Sticking or binding doors must be repaired by a 

qualified garage door installer prior to installation of the opener.

•  Remove or disengage all garage door locks and mechanisms prior to installation of the 

opener.

Entanglement 

•  Never plug in and operate opener prior to installation.
•  Keep hands and loose clothing clear of door and guides at all times.

Entrapment under  
operating door  

•  DO NOT operate the opener unless the garage door is in full view and free from objects 

such as cars and children/people. Make sure that the door has finished moving before 
entering or leaving the garage

•  In order for the opener to sense an object obstructing the door way, some force must 

be exerted on the object. As a result the object, door and/or person may suffer minor 
damage or injury.

•  Ensure the garage door is in good working order by undertaking regular servicing.
•  Install the optional wall transmitter in a location where the garage door is visible, but out 

of the reach of children at a height of at least 1.5m.

•  Photo Electric beams must be installed if the closing force at the bottom edge of the door 

exceeds 400N (40kg)

This automatic garage door opener is designed and tested to offer safe service provided it is installed and 

operated in strict accordance with the following safety warnings. Failure to comply with the following instructions 

may result in death, serious personal injury or property damage.

1. Safety Warnings!  (for installation)

Summary of Contents for PanelMax SDO-8V3





























Reviews: