background image

8

www.balmar.net   /   Customer Service: +1 (360) 435-6100 x1   /   Technical Support: +1 (360) 435-6100 x3

Tech Service is available Monday - Friday (8:30am - 7:30pm EST)

Preset, Multi-Stage Battery Programs  

                                                                       

Part Number:

Balmar Regulators

Digital

Duo 

Charge

Dual

Engine

Centerfielder

12 Volt

24 Volt

ARS-5 MC-614 MC-612-DUAL MC-624 DDC-12/24 CFII-12/24

Universal Factory Program, Deep Cycle 

Flooded, Gel Cell, Absorbed Glass Mat 

(AGM) and Spiral Wound Flooded (Optima)

Yes

Yes

Yes

Yes

Yes

Yes

Standard Flooded, Halogen Systems, Lithium

-

Yes

Yes

Yes

Yes

Yes

Balmar Alternator Models

6-Series Alternators (70A-150A)

Yes

Yes

Yes

Yes

Yes

Yes

AT-Series Alternator (165A-200A)

-

Yes

Yes

-

Yes

Yes

9-Series Large Case Alternators (140A-310A)

-

Yes

Yes

Yes

Yes

Yes

Multiple Alternator/Engine Configurations
Dual Engine, One Alternator Each

-

Yes (qty 2)

-

Yes (qty 2)

Yes

Yes

Single Engine, Two Alternators

-

-

Yes

Yes (qty 2)

Yes

Yes

Ignition

Connector 1

Conne

ctor

 

2

17

16

15

14

12

13

10

11

9

7

6

5

8

4

3

2

1

External Regulator

Plug

Positive Battery Sense

(Required for Internal Regulator Only)

Isolated Ground Terminal

MUST be connected to system ground

Positive Output

Terminal

HOUSE BATTERY

BANK

10A

1A

D+

+

Summary of Contents for Max Charge MC-614-H





















Reviews: