background image

Preface

iv

Qualification of Personnel

Make sure that all personnel have manufacturer-approved training applicable to the auxiliary equipment.

Personal Safety Equipment

Make sure that operators and maintenance personnel have all safety equipment applicable to the auxiliary 

equipment. Examples include safety glasses, protective headgear, safety shoes, etc.

Unauthorized Operation

Make sure that unauthorized personnel cannot gain access to the operation of the equipment.

Environmental Compliance

RoHS

The Aurora RM fully complies with RoHS regulations.

Waste Electrical and Electronic Equipment (WEEE) Directive

Panametrics is an active participant in Europe’s 

Waste Electrical and Electronic Equipment

 (WEEE) take-back 

initiative, directive 2012/19/EU.

The equipment that you bought has required the extraction and use of natural resources for its production. It may 

contain hazardous substances that could impact health and the environment.
In order to avoid the dissemination of those substances in our environment and to diminish the pressure on the 

natural resources, we encourage you to use the appropriate take-back systems. Those systems will reuse or recycle 

most of the materials of your end of life equipment in a sound way.
The crossed-out wheeled bin symbol invites you to use those systems.
If you need more information on the collection, reuse and recycling systems, please contact your local or regional 

waste administration.

EU Declaration of Conformity

The EU Declaration of Conformity (EU DoC) and other compliant documents can be downloaded from the Product 

Support Portal. 

WARNING!

Make sure that power to the auxiliary equipment is turned OFF and locked out before 

you perform maintenance procedures on this equipment.

Summary of Contents for Panametrics Aurora RM


















Reviews: