Baker Hughes Masoneilan 21000 Series, Instruction Manual

Page: 18 / 40

14 | Baker Hughes Copyright 2023 Baker Hughes Company. All rights reserved.
Assembly Torque Requirements
Valve Size
ANSI Class
Bolting Requirements
Torque Requirements
Minimum Maximum Pre-Load
inch mm Qty. Size (inch) Lbs.Ft N.m Lbs.Ft N.m Lbs.Ft N.m
.75
& 1
20 &
25
150 & 300 4 1/2 " -13NC-2A 25 34 66 89 5 7
600 4 1/2 " -13NC-2A 25 34 66 89 5 7
900 & 1500 4 1 " -8NC-2A 125 169 560 759 45 61
2500 4 1 " -8NC-2A 125 169 560 759 45 61
1.5
& 2
40 &
50
150 & 300 8 1/2 " -13NC-2A 25 34 66 89 5 7
600 8 1/2 " -13NC-2A 25 34 66 89 5 7
900 & 1500 8 7/8" -9NC-2A 100 136 300 407 30 41
1.5 40 2500 8 7/8" -9NC-2A 100 136 300 407 30 41
2 50 2500 8 1-1/8 " -7NC-2A 160 217 640 868 60 81
3
80
150 & 300 6 5/8" -11NC-2A 45 61 132 179 10 14
600 8 3/4 " -10NC-2A 80 108 230 312 20 27
900 & 1500 8 1-1/8 " -8NC-2A 225 305 830 1125 75 102
4 100
150 & 300 8 5/8" -11NC-2A 45 61 132 179 10 14
600 8 1 " -8NC-2A 125 169 560 759 45 61
900 & 1500 8 1-1/2 " -8NC-2A 400 542 2100 2847 115 156
6 150
150 & 300 12 5/8" -11NC-2A 45 61 132 179 10 14
600 12 1 " -8NC-2A 125 169 560 759 45 61
8 200 150 – 600 12 1-1/4 " -8NC-2A 235 319 1200 1627 100 136
Notes: 1. Do not exceed Maximum Torque values listed.
2. Tighten in increments until required torque levels are reached.
3. Reject assembly if metal-to-metal contact is not achieved after reaching Maximum Torque.
4. Torque requirements shown are for standard B7 studs and 2H nuts.
Bellows Bonnet Assembly Torque Requirements
Bolting Requirements
Torque Requirements
Minimum Maximum Increments Pre-Load
Qty. Size (inch) Lbs.Ft N.m Lbs.Ft N.m Lbs.Ft N.m Lbs.Ft N.m
8 1/2 " -13NC-2A 20 27 30 41 5 7 5 7
8 5/8" -11NC-2A 25 34 55 75 10 14 5 7
Notes: 1. Do not exceed Maximum Torque values listed.
2. Tighten in increments noted until required torque levels are reached.
3. Torque requirements shown are for standard B7 studs and 2H nuts.
Valve
Size
mm in.
25
&
40
1
&
1- 1/2
900 31 230 250 34
Min.
daN.m
Carbon Steel Bolting
Max.
Ft. Lbs. daN.m Ft. Lbs.
ANSI Class
Stud (9)
20 to 50 3/4 to 2
150 - 300
600
4,5
33 37
5
1/2” -13 NC - 2A
200 8 150 - 300 26 192 207 28 1- 1/4” - 8 NC - 2A
1
2
3 4
5
6 7
8
1
2
3
4
1
2
3 4
10
8
5
6
7
11
12
9
1
2
3
5
6
4
Size Qty
8
12
1500
35
260 295
40
1” - 8 NC - 2A 4
2500 40 295 370 50
5,5 40 48 6,5
80 3
150
300
600 8 60 63 8,5 5/8” -11 NC - 2A 6
19 140 148 20 3/4” -10 NC - 2A 8
100 4
150 - 300
600
8,5 63 70 9,5 5/8” -11 NC - 2A 8
28
207 220
30
1” -8 NC - 2A 8
150 6
150 - 300
600
8,5 63 66 9 5/8” -11 NC - 2A 12
28 207 221 30 1” -8 NC - 2A 12
8 60 63 8,5 5/8” -11 NC - 2A 6
23 170 184 25
Min.
daN.m
Stainless Steel Bolting
Max.
Ft. Lbs. daN.m Ft. Lbs.
3,5
26 30
4
26 192 207 28
4,5 33 37 5
23 *
170 * 184 *
25 *
7 52 59 8
28 207 221 30
9 66 74 10
Req’d. Torque
28 207 221 30
*
Only on 21000 threaded tr im valves. For quick-change tr im valves, use following torques .........
Figure 11 – Bolting Torques and Tightening Sequence