Baileigh BP-3142NC Operator'S Manual Download Page 2

Page: 2 / 48

Table of Contents

THANK YOU & WARRANTY .......................................................................................... 1

INTRODUCTION ............................................................................................................. 3

GENERAL NOTES .......................................................................................................... 3

SAFETY INSTRUCTIONS .............................................................................................. 4

SAFETY PRECAUTIONS ............................................................................................... 6

TECHNICAL SPECIFICATIONS ..................................................................................... 8

TECHNICAL SUPPORT ................................................................................................. 8

UNPACKING AND CHECKING CONTENTS .................................................................. 9

Cleaning ...................................................................................................................... 9

TRANSPORTING AND LIFTING .................................................................................. 10

INSTALLATION ............................................................................................................. 11

Anchoring the Machine .............................................................................................. 12

GETTING TO KNOW YOUR MACHINE ....................................................................... 13

ELECTRICAL ................................................................................................................ 15

OPERATION ................................................................................................................. 17

Tooling Selection and Set-up .................................................................................... 17

Setting the Ram End Position .................................................................................... 17

General Notes ........................................................................................................... 18

CHANGING AND ADJUSTING DIES ............................................................................ 19

Replacing Upper Die ................................................................................................. 19

Rotating/Replacing Lower Die ................................................................................... 20

Punch and Die Specifications .................................................................................... 21

BENDING ALLOWANCE .............................................................................................. 22

UNDERSTANDING SPRINGBACK .............................................................................. 22

MATERIAL SELECTION ............................................................................................... 22

LUBRICATION AND MAINTENANCE .......................................................................... 23

Hydraulic System ....................................................................................................... 24

ELECTRICAL SCHEMATIC .......................................................................................... 25

PARTS DIAGRAMS ...................................................................................................... 26

Base Assembly Parts Diagram .................................................................................. 26

Main Frame Assembly Parts Diagram ....................................................................... 27

Trunnion/Bending Arm Assembly Parts Diagram ...................................................... 28

Upper and Lower Ram Assembly Parts Diagram ...................................................... 29

Back Stop Slide Shaft Assembly Parts Diagram ........................................................ 30

Back Stop Assembly Parts Diagram .......................................................................... 31

Chain Tensioner Assembly Parts Diagram ................................................................ 32

Cylinder Assembly Parts Diagram ............................................................................. 33

Travel Limit Assembly Parts Diagram ........................................................................ 34

Linkage Assembly Parts Diagram .............................................................................. 35

Cross Plate Assembly Parts Diagram ........................................................................ 36

Tooling Assembly Parts Diagram .............................................................................. 37

Parts List ................................................................................................................... 38

Summary of Contents for BP-3142NC

















































Search results

Summary of Contents for BP-3142NC

Reviews:

Related manuals for BP-3142NC

Brands by name

Popular brands

Baileigh BP-3142NC, Operator'S Manual

Search results

Summary of Contents for BP-3142NC

Reviews:

Related manuals for BP-3142NC

Brands by name

Popular brands