BAHAMA Jumbrella Page 43 Important Information Manual Download | Manualshive

Page: 43 / 56

background image

Bahama

GmbH

made in Germany

Installation Manual | LED

Tel +49 (0)2265 998 0

Gewerbeparkstrasse 34

Edition: 10|2020

D-51580 Reichshof

Instruction Manual | LED-Lighting

Contents:

1.

Teaching the remote control and connecting up to 4 umbrellas to one remote control

2.

Remote control functions

3.

Connection via Wifi | App

1.

Teaching the remote control and connecting up to 4 umbrellas to one

remote control

1.

Connect the power supply to the
umbrella.

2.

Switch on the remote control.

3.

Select and press the zone to which
the umbrella shall be programmed.

4.

Press the learning switch on the LED
controller which is installed on the
umbrella center pole.

→

The LED strips flash.

5.

Select the desired light color using
the color selector on the remote.

To sync more than one umbrella to the remote control, repeat steps 3 through 5.

Several umbrellas can either be synced to one and the same zone or to different zones.

Resetting the controller:
-

Press and hold the learning switch until the LED strips flash and return to white
light.

«
...
41
42
43
44
45
...
»

Summary of Contents for Jumbrella

























































Reviews:

No comments

Related manuals for Jumbrella

Brand: Mamas & Papas Pages: 12

Brand: Bebe Care Pages: 8

Transat Easy B012002

Brand: Badabulle Pages: 12

KOLDING 3715400

Brand: Jysk Pages: 16

Brand: Mamas & Papas Pages: 16

Brand: Costway Pages: 20

Seasons Sentry UMB-955258 Series

Brand: Atleisure Pages: 39

Brand: paramondo Pages: 8

Brand: Costway Pages: 4

Brand: Delta Children Pages: 62

Brand: Flagger Joe Pages: 3

Lavallette LAVDN7PCSW-BLU

Brand: Hanover Pages: 15

MagnaLatch 3 Series

Brand: D&D Technologies Pages: 2

Universal Bassinet BAS

Brand: boori Pages: 4

Universal Bell Curved Bassinet B-BCBAS

Brand: boori Pages: 6

Brand: Geuther Pages: 6

Brand: Cosco Pages: 24

STONE HAVEN 4 IN 1 CONVERTIBLE CRIB

Brand: Oxford Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands