BAHAMA Jumbrella Page 47 Important Information Manual Download

Page: 47 / 56

Bahama

GmbH

made in Germany

Installation Manual | LED

Tel +49 (0)2265 998 0

Gewerbeparkstrasse 34

Edition: 10|2020

info

bahama.de

D-51580 Reichshof

www.bahama.de

Last but not least the LED controller should be added to your private wifi.
- click on

“Setting“

- click on

”C

onnect WiFi LED Controller to your home network

”

- select your wifi from the list and insert the corresponding password

10.

Re-connect your smartphone to your private wifi.

11.

You can now add more umbrellas to either the same room (simultaneous control) or to different
rooms (individual control).

12. Changing the room name and photo

click on

“

Setting

“

click on

”

Edit rooms Information

”

click on

“

Edit

“

click on the room name to change it | click on the
photo to take a new photo

Should you not be able to properly connect the LED controller, press the „Learning Switch“ on the controller until the LED st

rips flash

(min. 3 seconds). This will completely reset the controller. Repeat the aforedescribed steps.

Summary of Contents for Jumbrella

























































Search results

Summary of Contents for Jumbrella

Reviews:

Related manuals for Jumbrella

Brands by name

Popular brands

BAHAMA Jumbrella, Important Information Manual

Search results

Summary of Contents for Jumbrella

Reviews:

Related manuals for Jumbrella

Brands by name

Popular brands