manualshive.com logo in svg

Badger Meter Hedland MR, User Manual, Page: 6 / 40

Share
Download
Badger Meter Hedland MR User Manual Download Page 6

Installation

Installing the Transmitter

1  Disconnect the electrical power from the target system before making or changing any 

transmitter connections

2  Use 005 A fast-acting fuse if non-current limited power sources are used
3  Terminate cable shield connection at either DC ground or earth ground
4  Mount the transmitter so fluid is traveling in the direction of the flow arrow

Flow Direction Arrow

Flow Inlet

Figure 1:  Flow direction arrow

5  Install unit in desired location Use wrench on transmitter flats to hold the unit in place 

during installation DO NOT TURN the transmitter using the wrench 

6  After installation, rotate the transmitter by hand to view the display 
7  Capture the zero flow position on the meter cone using the ZERO CAPTURE procedure

Place wrench on transmitter flats on the 

same side plumbing is being tightened

Never place wrench on transmitter flats 

opposite plumbing being tightened

Rotate transmitter by hand only to view flow scale Never use wrench on flats to  

rotate transmitter

Figure 2:  Installing and rotating the transmitter

Page 6 

September 2017

XMT-UM-00498-EN-03

Summary of Contents for Hedland MR









































Reviews:

No comments