manualshive.com logo in svg

Badger Meter Hedland MR, User Manual, Page: 16 / 40

Share
Download
Badger Meter Hedland MR User Manual Download Page 16

Programming Procedures

Programming Flowcharts

See the following programming flowcharts for the menu structure of the MR flow 

transmitter and the available configuration selections:
• 

"Programming Flowchart for Water (Includes Water-Based Liquids)" on page 12

• 

"Programming Flowchart for Oil (Includes Petroleum-Based, Phosphate Ester and Caustic/

API Oil)" on page 13

• 

"Programming Flowchart for Air/Gases (Includes Caustic/Corrosive Gases)" on page 14

Basic Programming Descriptions

Display Mode (Display)

In 

Display

 mode, the meter can display 

RATE

 (flow rate) or 

TOTAL

 (total accumulated flow) 

or alternate between 

BOTH

 rate and total Edit with the 

"List Item Selection Procedure" on 

page 15

Rate Units of Measure (RATE UNT)

The meter lets you select from many common rate units Edit with the 

"List Item Selection 

Procedure" on page 15

Rate (Time) Interval (RATE INT)

The meter lets you select intervals based on time Edit with the 

"List Item Selection 

Procedure" on page 15

Total Units of Measure (TOTL UNT)

To display the 

Total Flow

, you must first select the engineering units for the total The 

monitor allows the choice of many common totalization units Edit with the 

"List Item 

Selection Procedure" on page 15

Total Display Multiplier (TOTL EXP)

The meter can accumulate the flow total in multiples of ten For example, if the most 

desirable totalization unit is 1000 gallons, the monitor can easily be set up for this 

requirement Once back in 

RUN

 mode, every time the total display increments by one digit 

the actual total would be an additional 1000 gallons At 1000 total gallons the total display 

would read 1, at 3000 gallons the total display would read 3 This feature allows the unit to 

accumulate totals that would exceed the 8-digit display capacity Table 2 lists the available 

selection choices Edit with the 

"List Item Selection Procedure" on page 15

Page 16 

September 2017

XMT-UM-00498-EN-03

Summary of Contents for Hedland MR









































Reviews:

No comments