background image

  To enter a new security code use the RIGHT arrow key 
to move the cursor under the digit to be changed and use 
the UP or DOWN arrow keys to change the digit to the 
desired value. The values can be from 0 to 9 and A to F. 
 
  After entering the security code, press the ENTER key 
and the following screen will appear: 
 

 

-STORING PARAMETERS- 

PARAMETERS>PROGRAMMED 

 
  This screen indicates that the new parameters have been 
stored in the recorder. The display will then return to the 
normal operating screen. This completes the Calibration 
Section. 

 
 
 
 

OPTION (FOR FLOW UNITS SCREEN) 

 
  Selecting OPTION in the Flow Units screen allows the 
entering of any three letter label for special engineering 
units. Press the ENTER key with OPTION selected and 
the following screen will appear: 
 

 

MEASUREMENT UNITS 

OPTION INITIALS=AAA 

 
  There will be a cursor under the first letter. Use the UP 
or DOWN arrow keys to select the desired letter. Press 
the RIGHT arrow key to move the cursor to the second 
and third letter and select the desired letter. Press the 
ENTER key to enter the OPTION INITIALS. The 
following screen will appear: 
 

 

DISPLAY FLOW LABEL AND 

TOTALIZER ? YES 

 
  This screen asks if the FLOW label is to be displayed 
on the normal operating screen. If the recorder is to be 
used to record temperature or some other measurement 
not related to flow or requires totalization, then selecting 
NO will remove the FLOW label and the totalizer value 
from the screen. Use the UP or DOWN arrow keys to 
select YES or NO and press the ENTER key. The 
following screen will appear: 
 

 

UNIT MULTIPLIER 

AAA  X  1,000 

 
  This screen allows the selection of the desired flow rate 
multiplier. Press the UP or DOWN arrow keys to select 
the desired multiplier and then press the ENTER key. The 

ollowing screen will appear: 

f

 

 

FULLSCALE UNITS=AAA 

FULLSCALE = 0000  X  1,000 

 
 
 
 
 

 
 
 
 
 
 
  This screen allows the entering of the full scale flow 
rate desired. Press the UP or DOWN arrow keys to select 
the desired value and the RIGHT arrow key to move the 
cursor under the digit to be changed. After the desired 
value is selected, press the ENTER key and the following 
screen will appear: 
 

 

OFFSET UNITS=AAA 

OFFSET=0000  X  1,000 

 
 
  This screen allows an offset value to be used instead of 
0 for a 4 mA input. If the input device has a value other 
than 0 for 4 mA, then that value would be entered into 
this screen. Press the UP or DOWN arrow keys to select 
the desired value and the RIGHT arrow key to move the 
cursor under the digit to be changed. After the desired 
value is selected press the ENTER key. 
 

 

TOTALIZER UNIT 

UNIT INITIALS=AAA 

 
 
  This screen allows the entering of the desired totalizer 
unit label. Press the UP or DOWN arrow keys to select 
the desired letter and the RIGHT arrow key to move the 
cursor under the letter to be changed. After the desired 
letters are selected press the ENTER key. The following 
screen will appear: 
 

 

TOTALIZER MULTIPLIER 

X  1,000 

 
 
  This screen allows the selection of the desired totalizer 
multiplier. Press the UP or DOWN arrow keys to select 
the desired multiplier and then depress the ENTER key. 
The following screen will appear: 
 

14

 

Summary of Contents for 3000+























Reviews: