• Leave the bottle warmer to cool for about 15 minutes before
using it again. Never touch the inside of the tank while the
appliance is in use, or immediately after use.
• Always unplug the appliance before cleaning or filling and after
each use.
• Do not leave the power cable at the edge of a table or work-
surface. Do not place it on a hot surface. Do not leave the
power cable dangling where a child could reach it.
• In the interests of safety, only use Babymoov accessories and
spare parts and never dismantle the appliance.
• Avoid using your appliance if it is not working properly or if it
is damaged. If this happens, contact the Babymoov after-
sales service.
Using the appliance in the car:
• Never use the bottle-warmer while the vehicle is in motion.
Leave your engine on when using the bottle-warmer to avoid
running the battery down.
• The cigarette-lighter adapter is specially designed for this bottle-
warmer: do not use it with other appliances.
• Regularly check your vehicle's cigarette lighter.
• Clean it as required.
• If you have just used your car’s cigarette lighter, let it cool down
for five minutes in the open position before plugging in the
bottle-warmer.
Points to respect for trouble-free use:
- Always check that the bottle is slightly open.
- Always remove the lid from the jar.
- Optimum heating will be guaranteed provided operation is not interrupted.
- Use tap water only, with no added product.
PLEASE NOTE: always use the adapter ring and the basket to warm up baby bottles and jars.
By using the amounts of water indicated in the tables below, a baby bottle or jar will be heated to 30 °C / 33 °C.
The quantities given are an indication only; if you think the result is too hot or not hot enough for your baby, don't hesitate to reduce
or increase the quantities of water.
Take care:
the quantities of water given correspond to a polycarbonate bottle without a removable base.
HOW TO USE
a.
Measuring device
b.
Warming tank
c.
Jar basket
d.
Adapter ring
e.
ON button
f.
Cigarette-lighter adapter
g.
Power cable
h.
Backlit ring
TULIPE HOME/CAR BOTTLE-WARMER •
Instructions for use
8
Amount of milk
in the bottle
Quantity of water to put
in the measure, when
the bottle has been
prepared with water at
room temperature.
Quantity of water
to put in the measure
for a bottle prepared
and placed in the
refrigerator.
60 ml 7 ml 10 ml
90 ml 8 ml 12 ml
120 ml 10 ml 12,5 ml
150 ml 11 ml 13 ml
180 ml 12 ml 13,5 ml
210 ml 13 ml 14 ml
240 ml 14 ml 14,5 ml
270 ml 15 ml 15 ml
300 ml 16 ml 15,5 ml
330 ml 17 ml 16 ml
Jar
Quantity of water
to put in the measure
for one jar.
Quantity of water
to put in the measure
for a jar kept in the
refrigerator.
120 g 10 ml 18 ml
200 g 12 ml 22 ml
250 g 15 ml 28 ml
Using the appliance at home
Put the bottle-warmer on a flat and steady
surface. Make sure the bottle-warmer's power
cable is out of the reach of children.
Plug the power cable into a power outlet.
1-2.
Fill up the measuring device
(a)
with
water by following the doses reported
here to the side and then pour the water
into the warming tank
(b)
.
3.
Put the baby bottle in the bottle-warmer's
warming tank
(b)
.
4.
If using a standard/small baby bottle, place
the adapter ring
(d)
around the bottle to
better warm up the contents.
5.
To warm up a jar, place it in the designated
basket
(c)
and then in the warming tank
(b)
.
6.
Press the ON button
(e)
to start the heating
cycle. The backlit ring
(h)
will turn red, which
means that the heating cycle is in progress.
CAUTION!
The steam that comes out during
the heating cycle is very hot. Do not put your
hands on the appliance when it is in use.
Summary of Contents for A002028
Page 2: ...2 ...
Page 3: ...3 1 4 7 8 9 5 6 2 3 a f g b d c h e ...
Page 46: ...46 ...
Page 47: ...47 ...
