background image

•  Do not immerse the appliance in water or other liquids. 
•  Always  inspect  the  appliance  before  use  for  noticeable 

signs of damage. Do not use if damaged, or if the appliance 
has been dropped. 

•  In the event of damage, contact the Conair Customer Care 

Line (refer to ‘UK After Sales Service’ section for further 
information).

•  Do not use the appliance if the lead is damaged. In the 

event of lead damage, discontinue use immediately. If the 
lead is damaged it must be replaced by the manufacturer. 
Return the appliance to the Customer Care Centre (refer 
to ‘UK After Sales Service’ section for further information). 
No repair must be attempted by the consumer.

•  Do  not  use  this  appliance  with  a  wrongly  adjusted, 

damaged or broken blade as injury may occur.

•  Only use the attachments supplied with this appliance.
•  Do not leave the appliance unattended when switched on 

or plugged in.

•  Do  not  place  the  appliance  on  any  surface  whilst  in 

operation.

•  Before use, check that the voltage supply corresponds to 

the voltage indicated on the appliance.

•  Maximum continuous operating time is 20 minutes; allow 

to cool for 10 minutes before proceeding.

•  Special care is required when using the appliance close to 

the ears, eyes, neck and face.

•  This appliance should not be used by adults whose reduced 

physical, sensory or mental capabilities, or whose lack of 
experience and knowledge, might cause a hazard, unless 

Summary of Contents for PRECISION V-BLADE CLIPPER













Reviews: