background image

8  |  Getting Started

www.BabyLock.com

Optional U.S. Grounding

GROUNDED OUTLET BOXES

METAL

SCREW

(B)

(C)

TAB FOR

GROUNDING

SCREW

GROUNDING PIN

(A)

This product is for use on a nominal 120 V or nominal 220 V circuit, and has a grounding plug that looks 

like the plug illustrated in sketch A above. A temporary adapter, which looks like the adapter illustrated in 

sketches B and C, may be used to connect this plug to a 2-pole receptacle as shown in sketch B if a properly 

grounded outlet is not available. The temporary adapter should be used only until a properly grounded 

outlet can be installed by a qualified electrician. The green colored rigid ear, lug, and the like, extending 

from the adapter, must be connected to a permanent ground such as a properly grounded outlet box cover. 

Whenever the adapter is used, it must be held in place by the metal screw. 

 

Â

IMPORTANT

: In Canada, the use of a temporary adapter is not permitted by the Canadian 

Electric Code.

Parts List

 

 

NOTE

: The parts photographed in this manual may look different from the ones you received.  

 

Item

Quantity

Photo

A. Pro-Stitcher Getting Started Guide (this guide)

1

Getting Started Guide for the Regalia

Model BLPS4-RG

B. Blue X-axis Flexirack (12 feet)

1

C. X-axis Flexirack clamps and screws

4

ADAPTER

Summary of Contents for Regalia BLPS4-RG



























Reviews: