Baby Jogger City Single Manual Download Page 29

Page: 29 / 60

FORW
ARD-F

ACING

Forward-Facing Harness Mode with Tether Strap:

10-30 kg (22-65 lb) and 69-125 cm (27-49

”

)

• Do NOT use the anti-rebound bar forward facing.

• Place the car seat forward-facing in the vehicle back seat

• Make sure UAS strap or vehicle seat belt is routed through the

forward-facing belt path

marked with an orange label

• Install this car seat tightly in your vehicle

Car seat

should not

move

at the forward-facing belt path more than 2

5 cm (1

”

)

from side to side and front to back

• Attach and tighten top tether strap

• Harness straps must be

at or just above

the top of child’s

shoulders and chest clip must be at

armpit level.

• Experts recommend that children ride rear-facing until the

age of 2 or until they reach the maximum rear-facing height or

weight rating for their seat

and when forward-facing

children

should use the built-in harness system for as long as possible

until they reach the maximum forward-facing weight or height

for their car seat

This car seat can remain rear-facing up to 18

kg (40 lb), up to 110 cm (43”) and forward-facing up to 30 kg

(65 lb), 125 cm (49”)

FORWARD-FACING HARNESS MODE AND TETHER STRAP SAFE

USE CHECKLIST

UAS STRAP WITH TOP

TETHER STRAP

DO NOT INSTALL BY THIS

METHOD FOR A CHILD

WEIGHING MORE THAN

20 KG (45 LB)

VEHICLE LAP/SHOULDER

SEAT BELT WITH TOP

TETHER STRAP

VEHICLE LAP ONLY

SEAT BELT WITH TOP

TETHER STRAP

Summary of Contents for City Single





























































Search results

Summary of Contents for City Single

Reviews:

Related manuals for City Single

Brands by name

Popular brands

Baby Jogger City Single, Manual

Search results

Summary of Contents for City Single

Reviews:

Related manuals for City Single

Brands by name

Popular brands