Baby Jogger City Single Manual Download Page 21

Page: 21 / 60

REAR-F

ACING

USING THE ANTI-REBOUND BAR

Note:

ALWAYS

use the anti-rebound bar in rear-facing modes

NEVER

use the anti-rebound bar when the car seat is used

forward-facing

Attach the anti-rebound bar to the front of the car seat

First

unsnap the seat pad from the side of the armrest

Then locate

the attachment slots

you may have to spread the fabric apart

with your fingers to see them clearly

Insert the anti-rebound bar into the car seat

Make sure the bar is not being installed upside-down

The text

“

THIS SIDE UP

”

should be read to ensure correct orientation

The anti-rebound bar is secure when it clicks into place on

both sides

Pull on each side of the bar to make sure it is

securely attached

Snap the seat pad fabric back onto the side of the armrest

WARNING!

The anti-rebound bar should only be used Rear-

Facing

Remove the anti-rebound bar when using this car seat

Forward-Facing

To remove the anti-rebound bar from the car

seat

First

push the release buttons marked with the label on

both sides of the car seat

Then pull the anti-rebound bar out of

the car seat

INSTALL REAR-FACING WITH UAS STRAP

THIS SIDE UP

CLICK

Summary of Contents for City Single





























































Search results

Summary of Contents for City Single

Reviews:

Related manuals for City Single

Brands by name

Popular brands

Baby Jogger City Single, Manual

Search results

Summary of Contents for City Single

Reviews:

Related manuals for City Single

Brands by name

Popular brands