Baby Jogger City Single Manual Download Page 37

Page: 37 / 60

BOOS

TER

Booster Use:

18-45 kg (40-100 lb)

110-145 cm (43-57

”

) and at least 4

years old

• Booster must be forward-facing in the vehicle back seat

• Vehicle seat belts

MUST

lay flat against child and

MUST NOT

be twisted

• Make sure vehicle seat’s lap belt is adjusted snugly

lays low on

the child’s hip

and is routed behind the armrest in the booster’s

belt path marked with a grey outlined label

• Make sure vehicle seat’s shoulder belt is centered between the

child’s neck and edge of shoulder

•

Never

use a vehicle lap only seat belt across front of child

•

DO NOT

position vehicle shoulder belt under the child’s arm or

back

•

DO NOT

allow child to slouch or slide down in the booster seat

•

DO NOT

position vehicle seat belt over top of armrests

• Vehicle seat’s headrest

SHOULD NOT

create a gap between

vehicle seat and booster seat

• The front of booster seat base

MUST NOT

hang over front of

vehicle seat

• If child will not keep the vehicle seat belt properly positioned

DO NOT

use this booster seat

Use a car seat with a 5-point

harness or a different booster seat

• Experts recommend that children should use a 5-point harness

system car seat for as long as possible until they reach the

maximum forward-facing weight or height for their car seat

After reaching the maximum forward-facing weight or height

they also recommend that children 145 cm (4 feet 9 inches)

tall or under should ride in a belt-positioning booster seat

This

car seat can be used forward-facing up to 30 kg (65 lb) and

up to 125 cm (49 inches)

BOOSTER SAFE USE CHECKLIST

VEHICLE LAP/SHOULDER

SEAT BELT

NEVER USE A VEHICLE

LAP ONLY SEAT BELT

ACROSS FRONT OF CHILD.

Summary of Contents for City Single





























































Search results

Summary of Contents for City Single

Reviews:

Related manuals for City Single

Brands by name

Popular brands

Baby Jogger City Single, Manual

Search results

Summary of Contents for City Single

Reviews:

Related manuals for City Single

Brands by name

Popular brands