22
23
2. VEHICLE INSTALLATION POINTS
WHERE:
In the vehicle rear seats.
HOW:
GROUP 0+ • Install rearward facing.
GROUP 1 • Install forward facing.
GROUP 2/3 •Install forward facing.
In seats with:
ISOFIX anchorages (between seat and backrest) and Top Tether anchor points
(eg in the tray, on the floor or behind the backrest) and 3-point belt (vehicle
belt).
NOTICE:
The child seat must only be used in this seat IF it has ISOFIX anchorages, top
tether points a lap and diagonal belt (3 points).
Please, do NOT install the safety seat in forward seats except for the following
cases:
1. Whenever the vehicle does not count with rear seats.
2. When all rear seats are already occupied by children exceeding 135 cm
height.
3. When it is not possible to install all child restraints systems in the rear
seats.
2
1
*Note: According to Spanish legislation for child restraint systems (Royal Decree 667/2015).
3. GENERAL SEAT USE
3.1. How to use the harness buckle
1. Bring the two clasps together (fig. 3.1).
2. Make sure the correct side is facing up (fig. 3.2).
3. Fasten the two clasps together before inserting them into the harness
buckle. You should hear a click (fig. 3.3).
4. Pull the harness adjustment belt
(H)
o that the part of the strap that covers
the lap is not loose, ensuring the harness is taut and the buckle closed.
Open the harness buckle
(F)
by pressing the red button (fig.3.4).
3.2. Harness buckle care
In order to ensure child safety it is essential that the harness works correctly. If
this is not the case it is probably because of an accumulation of dirt or foreign
bodies.
Incorrect operation is understood as:
• The buckle clasps are notably slow to release when the red button is
pressed.
• The buckle clasps cannot be inserted (they fall out when they are inserted
into the buckle).
• The buckle clasps come together without making a click.
• It becomes difficult to insert the clasps into the buckle (resistance is felt).
• The buckle only opens when forced.
• Solution
Clean the harness buckle so that it works properly.
3.3. Cleaning the harness buckle
1. Open the buckle
(F)
(press the red button).
2. Hold the metal plate from below in a vertical position (fig. 3.12).
3. Slide the metal plate along the slot (fig. 3.5 y 3.6).
4. Remove the buckle
(F)
(fig. 3.7).
5. Steep the buckle
(F)
in hot water and neutral liquid detergent for at least
one hour. Rinse and dry it.
3.4. Removing the 5-point harness
1. Loosen the harness straps by pulling them at the point where they cover the
chest while pressing the harness adjustment button
(G)
(fig. 3.8).
2. From the back of the seat (fig. 3.9), Locate the harness strap connector and
unclip the harness straps
(E)
, freeing them from the connector, then remove
them by pulling them from the front of the seat (fig. 3.11).
3. Free the shoulder protectors
(C)
by unfastening them from the connector
that joins them (located at the back of the seat) or, in the event they
are joined without a connector, by passing them directly through the
corresponding holes in the seat. (fig. 3.11).
4. Lift the fabric cover and keep the harness straps folded in the corresponding
seat hollow so that they do not disturb the child. Replace the cover in its
place.
5. Turn the seat over and, from the back, free the belt buckle
(F)
by passing
the retention plate through the slot in the seat (fig. 3.12).
6. Remove the belt buckle
(F)
and save it in the storage bag.
Summary of Contents for REVOLTA
Page 21: ...40 41 ...
