manualshive.com logo in svg

BAB TECHNOLOGIE APPMODULE IP, Documentation, Page: 57 / 62

Share
Download
BAB TECHNOLOGIE APPMODULE IP Documentation Download Page 57

APP

MODULE Documentation 

 

 

 

 

  

BAB TECHNOLOGIE GmbH  57 

 

 

 

Figure 56: Downloading backup 

 

RESTORING A BACKUP 

 

Select an 

APP

MODULE backup file using the “Select backup file” button. The files have the 

extensions “*.apm.bkp”. 

 

 

Information for the selected file is displayed in the “Backup created on”, “Firmware version” 

and “Comments” fields. 

 

 

The “Modules” field shows which modules are available in the selected backup file. You can 

also use the checkboxes to select which modules are to be restored. 

 

 

Configuration:

 All configuration data except for the app configuration data. 

 

Note: The network settings are not part of the backup file. 

 

 

Statuses & logging:

 The address status table and logging table are restored. This is important, as 

it ensures you can access the status information in the apps after restore. 

 

 

Apps and app instances:

 Restores the app-related data. Individual apps and instances can be 

selected for restore from the drop-down menu (see figure above). 

 

 

 

Summary of Contents for APPMODULE IP































































Reviews:

No comments