manualshive.com logo in svg

BAB TECHNOLOGIE APPMODULE IP, Documentation, Page: 47 / 62

Share
Download
BAB TECHNOLOGIE APPMODULE IP Documentation Download Page 47

APP

MODULE Documentation 

 

 

 

 

  

BAB TECHNOLOGIE GmbH  47 

 

 

7.1

 

INSTANCE 

As soon as the App is installed, you can create so called “Instance”. An Instance is one of several objects 

of the same class.  

 

In order to create an instance, click on the following symbol "Create Instance".  

 

 

Figure 44: Create Instance 

 

With the icons on our site, you can start instances, edit parameters, display the LOG, copy or delete 

instances. 

 

Figure 45: Instance functions 

 

 

Colour 

Function 

Red

 

Start instance 

Yellow

 

Edit parameter 

Blue

 

Display log 

Green

 

Copy instance 

Orange

 

Delete instance 

 

 

7.1.1

 

NOTATION OF GROUP ADDRESSES 

The group addresses in the 

APP

MODULE can either be displayed in 2-digit notation ([XX/XXXX]) or 3-

digit notation ([XX/X/XXX]). The 

APP

MODULE 

always

 converts the group addresses into 3-digit display, 

no matter in which way they were entered.  

 

Note: Virtual group addresses (16... 31) can be used internally to control interoperations between the 

apps. The virtual group addresses are not sent to the bus. 

 

 

Summary of Contents for APPMODULE IP































































Reviews:

No comments