manualshive.com logo in svg

BAB TECHNOLOGIE APPMODULE IP, Documentation, Page: 11 / 62

Share
Download
BAB TECHNOLOGIE APPMODULE IP Documentation Download Page 11

APP

MODULE Documentation 

 

 

 

 

  

BAB TECHNOLOGIE GmbH  11 

 

 

2.1

 

LED STATUS 

The 

APP

MODULE has two DUO LEDs ("Power/Boot" and "Status"). Each DUO LED has a green and a red 

LED.  

 

POWER / BOOT LED 

LED display 

Status 

OFF 

The device is not ready for operation. No operating 

voltage is supplied. 

GREEN 

The device is ready for operation. 

FLASHING ORANGE 

The device is booting. 

 

STATUS LED 

LED display 

Status 

OFF 

The device is booting. 

FLASHING GREEN 

The device has been started; the LED simulates a 

"heartbeat". The flashing interval increases 

depending on the device utilisation.  

FLASHING RED 

Communication takes place via KNX.  

 

 

Explanation: 

 

The green "Power/Boot" LED lights up as soon as the 

APP

MODULE is supplied with power. Two to three 

seconds after the power supply has been switched on, this LED also starts to flash red (flashing orange) 

until the booting process has been completed. Then the LED is permanently illuminated green, while 

the "Status" LED flashes green (simulates a "heartbeat"). The flashing frequency increases depending on 

the device utilisation.  

 

It takes approx. 

2 minutes

 

to start the 

APP

MODULE. 

 

 

 

Summary of Contents for APPMODULE IP































































Reviews:

No comments