background image

17.  Install the faceplate using 3/16”  Allen wrench 

and torque the faceplate screws in a cross 

pattern to 25 in-lbs.

TENAYA2® SERIES

 

Relamping & Accessories

RELEASE DATE

12-6-16

REFERENCE

 

NUMBER

INS-2145-00

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900 

www.bklighting.com • [email protected]

B-K LIGHTING

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

11. Install reflector by placing in LED reflector 

holder, then twisting gently to the right under 

tabs.

12.  Place accessory holder onto tabs on accessory 

bracket, lined up with notches in holder.

10. Place accessory holder on OptiLock™, lining 

up holes in bracket on OptiLock™. Tighten (2) 

#6-32 set screws to secure accessory bracket to 

OptiLock™ as shown. 

15. Before Installation of faceplate, clean solid 

silicone faceplate gasket (see arrows) and collar 

of debris for a proper seal.

 FAILURE TO DO THIS STEP WILL CAUSE 

FIXTURE TO FAIL AND VOID PRODUCT 

WARRANTY.

13. 

If your Tenaya2® comes with optional 

accessory holder, see “Relamping with 

Accessory Holder” to remove and install 

source.

  To aim the OptiLock™ inside the optical 

chamber horizontally 360°, rotate the optical 

chamber to desired direction.

16. 

For Optional Internal Cutoff:

 Place internal 

cutoff louver in the top of the optical chamber 

in the desired direction of cutoff and install 

faceplate as normal. 

Optional Internal Cutoff

14. To aim the OptiLock™ inside the optical 

chamber vertically, loosen the four (4) #10-

24 screws using 1/8” Allen wrench and tilt 

OptiLock™ to desired vertical direction. Tighten 

all screws when aiming is complete. 

Summary of Contents for Tenaya 2 Series










Reviews: