background image

1.  Remove temporary cover.  

Installation

9.  

For concrete installation: 

Fill the hole around the 

fixture housing to 12” below the finished grade with 

clean fill dirt and tamp carefully to prevent settling 

of fixture. Pour concrete and finish as required flush 

with the top surface of the temporary cover.

OPTIONAL GROUT MASK INSTALLATION 

(IF ORDERED)

8.  

For soil installation: 

Fill and tamp soil to the 

appropriate height leaving room for sod, pavers, 

etc. to be level with the top of the temporary cover.

 Soil installation is not drive-over rated. 

OPTIONAL GROUT MASK INSTALLATION 

(IF ORDERED)

9.  

For concrete installation: 

Fill the hole around the 

fixture housing to 12” below the finished grade with 

clean fill dirt and tamp carefully to prevent settling 

of fixture. Pour concrete and finish as required flush 

with the top surface of the grout mask.

3.  Wipe inside of housing where HydroLock plate 

will sit clean of debris before inserting patented 

HydroLock plate on to junction box. Align HydroLock 

plate with pins in housing and seat it firmly in place. 

5. Connect transformer assembly to Patented 

HydroLock Barrier plate with quick disconnect.

WIRING DIAGRAM FOR USE WITH:

 

- MR16

 

- PAR36/AR111

2.  Make watertight connections using waterproof 

wire connectors (included) to leads on the bottom 

of Patented HydroLock Barrier Plate Assembly.  

See wiring diagram.

4.  Turn HydroLock

 

Barrier Plate clockwise ¼” to lock.

 

Patented

 

HydroLock Barrier Plate must be 

completely seated to ensure proper seal or 

water may intrude. This step must be done as 

stated or you will void your warranty.

HOT (BLACK)

NEUTRAL (WHITE)

HY
DROL

OCK

PL

AT

E

XFMR

or

TR

ANSF

ORME

R

GROUND (GREEN)

HOT

NEUTRAL

GROUND

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

Standard Instructions

HP2

INTEGRAL TRANSFORMER - STANDARD MR16 & PAR36/AR111

RELEASE DATE

08/28/2023

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900 

www.bklighting.com • [email protected]

B-K LIGHTING

REFERENCE NUMBER

INS-2858-00

B

-K

 LIGHTIN

G

B

-K

 L

IG

HT

IN

G

AIM

 AR

RO

W

 T

O

W

A

R

D

     

     

    

     

     

   S

U

R

FA

CE

 T

BE

 LI

GH

TE

D.

DO NO

T R

EM

OV

TE

M

PO

R

A

R

Y

 C

O

V

E

R

 U

N

T

IL

 H

O

U

SI

N

IS

 A

LIG

NE

D!

 F

A

IL

URE 

TO

 

A

LI

GN

 H

OU

SI

NG

 

PR

OP

ER

LY WILL

 

RES

UL

T I

N

 

FA

CE

PL

ATE

 

M

ISA

LI

GNM

EN

T!

IMPORTANT!

Read  Product Installation 

Instructions Before Install.

Scan  for 

Soil  Prep. 

Guide.

Summary of Contents for HP2 SERIES









Reviews: