7. Attach tether wire under screw head at the base
of the UPM housing and tighten. Slowly lower
the faceplate until tether is taut.
NOTE: Faceplate tether supplied with UPM
is designed as an installation aid and NOT a
safety cable. Do not add weight to, or drop
faceplate.
RELEASE DATE
3-15-1
REFERENCE NUMBER
INS-24 4-01
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
6. If UPM housing is not level, remove UPM housing;
loosen but
DO NOT REMOVE
(2) #8-32 screws
with 9/64” Allen wrench on CamLock™ assembly.
Adjust CamLock™ assembly up to 30° as needed
to level. Tighten the screws and reattach UPM
housing.
A
B
C
1. Install standard 4.5” x 2.85” recessed junction box
(By Others) in the final fixture location according
to designed lighting plan.
NOTE: Vertical or horizontal installation of
recessed junction box determines orientation
of UPM.
2.
Pull branch circuit wiring necessary for installation
(By Others.)
3. Feed branch circuit wiring and lamp leads to
remote mounted fixture through mounting plate
with CamLock™ assembly. Attach mounting plate
with supplied (2) #6-32 stainless steel hex drive
fasteners to recessed junction box using a 5/64”
Allen wrench.
4. Feed wire into UPM housing. Install housing
on CamLock™ at 90° to finished orientation as
shown. (Figure A)
5. Rotate housing 90° counter-clockwise (Figure
B). Tighten set screw with 5/64” Allen wrench
on outside of UPM housing to lock in place.
(Figure C)
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
PM2RM RECTANGULAR CAMLOCK™
Inspiration Control System
iOS device (Not Included) with installed B-K Lighting Inspiration Application required for use.
8. Use waterproof wire connectors (By Others)
to connect driver primary leads to branch
circuit wires. Connect incoming ground and
driver ground to ground wire provided in UPM
housing. See wiring diagram.
Number of wires and connections varies
with wiring as per lighting plan.
Ground
Hot
Neutral
WIRING DIAGRAM - Wireless Bluetooth® Controls
with Inspiration Application on iOS device
LINE
MODULE
COM
Remote
Driver
Red
Black
iOS
Bluetooth®
GROUND
iOS device must be within 5ft of fixture for
wireless operation.
iOS device controls dimming, CCT, Saturation,
and Hue using Bluetooth® wireless controls and
the application.
LINE
MODULE
COM
GROUND
Remote
Driver
10V
0V
0-10V DIM -
0-10V DIM +
Red
Black
0-10V CCT +
0-10V CCT -
Dimming
Continuous
CCT
10V
0V
iOS
Bluetooth®
WIRING DIAGRAM - Hybrid
Secondary wiring from remote driver connects
to fixture leads. 0-10V dimming connects to
module. 0-10V Continuous CCT connects to
module. iOS device controls CCT, Saturation,
and Hue.
iOS device must be within 5ft of fixture for
wireless operation.
LINE
MODULE
COM
GROUND
Remote
Driver
10V
0V
0-10V DIM -
0-10V DIM +
Red
Black
0-10V CCT DIM +
0-10V CCT DIM -
Dimming
Continuous
CCT
10V
0V
WIRING DIAGRAM - 0-10V Wired
Secondary wiring from remote driver connects
to fixture leads. 0-10V dimming connects to
module. 0-10V Continuous CCT connects to
module and controls CCT, Saturation, and Hue.
iOS device must be within 5ft of fixture for
wireless operation.
