background image

10. Attach tether wire under screw head at the base

of the UPM housing and tighten. Slowly lower
the faceplate until tether is taut. 

NOTE: Faceplate tether supplied with UPM is
designed as an installation aid and NOT a
safety cable. Do not add weight to, or drop
faceplate.

REVISION DATE

7-27-09

REFERENCE NUMBER

INS-1515B

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

PM1RM RECTANGULAR CAMLOCK™

Recessed junction box installation

Ground

Hot

Neutral

LINE (BLACK)

NEUTRAL (WHITE)

GROUND (GREEN)

BARE WIRE IN UPM

BLACK

WHITE

XFMR

RED

RED

TO FIXTURE

Wiring Diagram.

8.

Pull secondary leads into UPM housing and
connect to transformer secondary leads using
approved wire connectors (By Others). 

6.

If UPM housing is not level, remove UPM
housing; loosen but 

DO NOT REMOVE

(2) #8-32

screws with 9/64” allen wrench on CamLock™
assembly. Adjust CamLock™ assembly up to 30°
as needed to level. Tighten the screws and
reattach UPM housing. 

7.

Use wire connectors (By Others) to connect
transformer primary leads to branch circuit wires.
Connect incoming ground to ground wire
provided in UPM housing. See wiring diagram.

11. Make sure UPM body gasket is free of any dirt or

debris. Attach the faceplate by tightening the (4)
#6-32 captive screws evenly to 6-9 in/lbs using a
5/64” allen wrench.

9.

Remove the backing from adhesive tape on
transformer, place in bottom of UPM housing
void of any wiring and press firmly for five
seconds to ensure good contact.

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

ETL LISTED

 CONFORMS TO ANSI/UL

STANDARD 1598

CERTIFIED TO CAN/CSA

STANDARD C22.2 NO. 250

Summary of Contents for CamLock UPM PM1RM










Reviews: