B.E.G. LUXOMAT LK-IP/KNXs REG Operating Manual Download Page 32

Page: 32 / 39

Operating Manual

LK-IP/KNXs REG

90403

Individually addressed telegrams

Broadcast telegrams

Repetition of group telegrams

Repetition of individually addressed telegrams

Repetition of broadcast telegrams

Disabling

No individually addressed telegram is routed to KNX.

Route

All individually addressed telegrams are routed to KNX.

Filter

The individual address is used to check whether the received individually

addressed telegram should be routed to KNX.

Disabling

No received broadcast telegram is routed to KNX.

Route

All received broadcast telegrams are routed to KNX.

Disabled

The received group telegram is not resent to KNX in case of a fault.

Enabled

The received group telegram is resent up to three times in case of a fault.

Disabled

The received individually addressed telegram is not resent to KNX in case of

a fault.

Enabled

The received individually addressed telegram is resent up to three times in

case of a fault.

Disabled

The received broadcast telegram is not resent to KNX in case of a fault.

Enabled

The received broadcast telegram is resent up to three times in case of a fault.

Summary of Contents for LUXOMAT LK-IP/KNXs REG








































Search results

Summary of Contents for LUXOMAT LK-IP/KNXs REG

Reviews:

Related manuals for LUXOMAT LK-IP/KNXs REG

Brands by name

Popular brands

B.E.G. LUXOMAT LK-IP/KNXs REG, Operating Manual

Search results

Summary of Contents for LUXOMAT LK-IP/KNXs REG

Reviews:

Related manuals for LUXOMAT LK-IP/KNXs REG

Brands by name

Popular brands