background image

INSTRUCTION MANUAL

Technical changes reserved 
 B+B 0141 0315-117 September 2010

B+B Thermo-Technik GmbH | Heinrich-Hertz-Straße 4 | D-78166 Donaueschingen 

Fon +49 771 83160 | Fax +49 771 831650 | [email protected] | bb-sensors.com

07 / 12

1.   Points to be observed during operation

a.) Make sure to apply correct operating voltage as low or damaged battery will lead to measuring inaccuracies. If 

„BAT“

  

  is shown in the display or are the measurements obviously wrong the battery has been used up and needs to be  

 replaced.

  Please note:

  If the battery voltage falls even lower the voltage may not be sufficient for 

„BAT“

 to be displayed so that there will  

  be no 

„BAT“

 indication although the battery has been used up. We recommend to make it a rule to always check  

  the battery if the values indicated seem to be completely out of range.

b.) Make sure to maintain device properly and to operate it in accordance with the specification listed (do not throw, 

 

  knock etc.).

c.) Make sure that sensor and device are always subjected to the same temperature, i.e. try to avoid holding sensor  

  plug in your hand for a longer periode of time as well as subjecting device to an additional heat source as this may  

  result in measuring inaccuracies.

d.) Mains operation: When using a power supply unit please note that operating voltage has to be 10 to 12 V DC. Do 

 

  not apply overvoltage!! Cheap 12V-power supply units often have excessive no-load voltage. We, therefore, 

 

  recommend using regulated voltage power supply units. Trouble-free operation is guaranteed by our power supply  

  GNG10/3000.

  Prior to connecting the plug power supply unit with the mains supply make sure that the operating voltage stated at  

  the power supply unit is identical to the mains voltage.

e.) The battery has to be taken out, when storing device above 50°C. It is recommended to take the battery out, when  

  storing device for a longer period of time

f.)  The length of the measuring sensor (GTF300) can be reduced as desired so that it will be fully operational again 

 

  after sensor has been broken. To do so, please strip both wire ends for approx. 10mm and twist well. Measurements 

 

  are not possible as long as wire ends are exposed.

Summary of Contents for HM 1150













Reviews: