Azbil BH-101G0N0000 Specifications & Instructions Download Page 16

16

AB-7333

 

„

Indicators

Figure 7. Indicator positions

Item

Product indicator

Color

State

Description

Power indicator

POWER

Green

Lit

Power ON

Flashing Power ON

(Lithium ion capacitor module being 
charged)

Not lit

Power OFF

System error indicator

ERROR

Red

Lit

Abnormal

Note: Contact Azbil Corporation.

Flashing

Not lit

Normal

Active indicator for redundant 

product configuration

ACT

Green

Lit

The device is operating (active).

Not lit

The device is for backup (standby).

Storage access indicator

STORAGE

Green

Lit

The data storage is being accessed.

Not lit

The data storage is not being accessed.

ETHERNET communication 
indicator

LAN1 100
LAN2 100 (not used)

Green

Lit

A link is established at 100 Mbps.

Flashing Data is being received or transmitted at 

100 Mbps.

Not lit

A link has not been established.

LAN1 1000
LAN2 1000 
(not used)

Green

Lit

A link is established at 1000 Mbps.

Flashing Data is being received or transmitted at 

1000 Mbps.

Not lit

A link has not been established.

System indicator

Indication using 
7-segment LED

Blue

Normal

The four 7-segment LEDs are lit in 
sequence at their outer edges at an 
interval of two seconds.

Abnormal Indication other than above.

DI status indicator

DI ch1–ch8

Green

Lit

DI status is ON.

Not lit

DI status is OFF.

DO status indicator

DO ch1 and ch2

Green

Lit

DO status is ON.

Not lit

DO status is OFF.

Indicator (not used)

IN

OUT

LAN1 100 1000

DI1  DI2  DI3  DI4

POWER

DI5  DI6  DI7  DI8

D01 D02

ERROR

ACT

STORAGE

7-segment LED

LAN2 100 1000 (not used)

REDUNDANT IN OUT (not used)

Summary of Contents for BH-101G0N0000





















Reviews: