Azbil BH-101G0N0000 Specifications & Instructions Download Page 1

1

 

Specifications/Instructions

AB-7333

Supervisory Controller

© 2017–2020 Azbil Corporation. All Rights Reserved.

„

Overview

This product (Model BH-101G0_0000) is a Supervisory 
Controller that collects information about a primary device 
(such as a controller) and provides that information to the 
Client PC in savic-net

 G5, Azbil Corporation's building 

management system.
This product receives point information from the primary 

device through periodic scan or state change notifi cations 

and accumulates and manages various kinds of control-
related data.
In addition, the software that can be downloaded from this 
product allows you to monitor its state using graphics and 
lists, set up several different kinds of controls including 
interlock controls and scheduling, view data such as 
charts as well as daily, weekly, monthly and yearly reports, 
and perform other operations from the Client PC.
This product can also provide information to a third-party 
BACnet device.

„

Features

Any combination of the following applications is available 
as required.

Equipment status monitoring 
This product monitors up to 5000 points of the data 
below. 

    

It is possible to connect up to 30 Supervisory Controllers 
to monitor up to 150,000 points.  

 

Each  Supervisory  Controller  can  also  be  confi gured 
for  redundancy.  (If  a  redundancy  confi guration  is 

implemented, up to 60 Supervisory Controllers can be 
connected.) 

Point information in the primary device

Direct inputs to ensure immediate detection of 

power supply state and fi re alarms from a building

Comprehensive control 
This product comprehensively controls the devices 
connected to the system to realize comfort, safety, and 

energy effi ciency.

Data management 
This product stores and manages the following data:

Data collected from the devices connected to this 
product

Data transmitted from the devices connected to 
this product

Data that has been processed for daily, weekly, 
monthly, and yearly reports based on the collected 
and transmitted data

Data visualization 
By using the software that comes with this product, 
you can display graphics, charts, and daily, weekly, 
monthly, and yearly reports on the screen of a Client 

PC or output them to a fi le.

Summary of Contents for BH-101G0N0000





















Reviews: