Ayrton Khamsin, User Manual

Page: 9 / 20

USER MANUAL _
9
THE KHAMSIN DMX ADDRESS SETTING
All luminaires must have a DMX start address correctly set when using a
DMX signal to control them. The DMX start address is the channel from
which the luminaire “listens” to the digital control information sent by the
DMX controller.
The start address must conform to the one set on the DMX controller to
control the luminaire. This address is the DMX value that appears on the
luminaire’s display. You can set the same address for all the luminaires, or
some of them, but you can also set a different address for each luminaire,
as needed.
If you do set the same address for all the luminaires, they will all “listen”
from the DMX channel you have set. The instructions sent by the DMX
controller will affect all luminaires at the same time. If you set a different
address per luminaire, the DMX controller can control each independently.
If, for instance, the fixtures are preset in 64-channel DMX mode (required
for full control), you will need to adjust the DMX address for the luminaires
as follows: The first unit with DMX address 001, the second with DMX
address 065 (64 + 1), the third with DMX address 129 (64 + 65), etc.
CONTROL PANEL (MENU OPTIONS)
AA large number of settings are accessible from the fixture’s control panel.
A good working knowledge of it will enhance the fixture’s possibilities.
You can access the Main Menu by clicking the jog wheel.
Turning the jog wheel performs cycling through the menus:
Display can be activated without external power source if optional battery
is installed into the unit.
Battery specs are:
The fixture’s menu functions are described in the following table:
Table 1: KHAMSIN MENU FUNCTIONS AND OPTIONS
Address Address DMX address:001-XXX: DMX address setting
Mode
User Mode Stand Mode
Basic Mode
Extend Mode
User Mode A
User Mode B
User Mode C User’s mode to change
channel numbers
Edit User ModeA: Max channel
PAN : Preset User modes
A,B,C:
Options
Status No DMX Mode
Pan Reverse
Tilt Reverse
Pan Degree
Feedback
Pan/Tilt Spd
Hibernation
Art-Net to DMX Close/Hold/Auto
ON/OFF
ON/OFF
630/540
ON/OFF
Speed 1~ 4
OFF , 01M~99M
ON/OFF Auto run if no DMX
Pan Reverse movement
Tilt Reverse movement
Pan Degree Select
Movement Feedback
Movement Speed
Stand by Mode
Art-Net to DMX
Service PIN Service PIN
Set IP
Crossload SW Password=XXX
xxx.xxx.xxx.xxx
Service Password”=050”
Set IP
Uploading Software
Fans Control Head Control Auto
Stage
Studio
Silent Fans Speed select
Disp.Setting Shutoff Time
Flip Display
Key Lock
DispFlash 02~60m 05m
ON/OFF
ON/OFF
ON/OFF Display shutoff time
Reverse 180 degree
Key Lock
DispFlash
Signal Select DMX
WDMX
Art—Net
sACN DMX
WDMX
Art—Net
sACN
Temp. C/F
Celsius
Fahrenheit
Temperature °C/°F
Initial Pos. PAN =XXX Initial effect position
Wireless DMX Activate WDMX
Act&Data Out
Rest WDMX Activate WDMX
Act&Data Out
Rest WDMX
Dim Curve Square Law
Linear Dimming curve
Refresh Select 1.2K
2.4K
16K Frequency
Trigger DMX Value Disp.
Set To Slave
Auto Program PAN……
Slave1,Slave2,Slave3
Master / Alone DMX Value Disp.
Set To Slave
Auto Program
Reset Default ON/OFF Restore factory sett.
Info
Time Info. Current Time
Ttl Life Hrs
Last Run Hrs
Timer PIN
Clr Last Run XXXX(Hours)
XXXX(Hours)
XXXX(Hours)
Password=XXX
ON/OFF
Temp. Info Head Temp. XXX °C/°F
Software Ver V1.0... Software version
Network IP,Mask,Mac Network setting
Test
Home All
Pan&Tilt
Color
Gobo
Other Reset All
Reset Pan&Tilt
Reset Color
Reset Gobo
Reset Others
Test Channel PAN …… Test function
Manual Ctrl. PAN =XXX
: Manual control of
parameters
Calibration --Password--
PAN
: Password “050”
Calibrate and adjust the
home position
Preset
Select Prog. Prog. Part 1 = Program 1 ~ 10 Program 1
Prog. Part 2 = Program 1 ~ 10 Program 2
Prog. Part 3 = Program 1 ~ 10 Program 3 Select the program to
be run
Edit Prog. Program 1
:
Program 10 Program Test
Step 01=SCxxx
Step 64=SCxxx Edit program
Edit Scenes Edit Scene 001
~ Edit Scene 250 Pan,Tilt,……
--Fade Time--
--Scene Time--
External input Edit scene
Scenes Input XX~XX Scenes Input