background image

Operating instructions and warnings

General instructions

- Only use water-based smoke machine fluid. This device is not suitable for oil-based smoke fluids.
- Ayra recommends using Ayra brand fluids with this smoke machine. This device is optimised for use with 
these fluids. 
- Fluids by other brands may shorten the lifespan of this device as a result of residue left behind in the 
pipework. 
- Using fluids by other brands can cause the smoke machine to spray hot fluid with the clouds of fog. 
- It is recommended to empty the fluid tank before transport.
- Fluid can remain in the tank as long as the device is held upright during transport and the tank contents 
does not exceed 50%. As the lid of the tank is not water-tight, fluid splashing around inside the tank during 
transport could cause leakage.
- When the device is turned on, it needs to be positioned in such a way so that it can be monitored at all 
times. 
- The device should be connected to a power source that can be disconnected immediately in case of 
emergency. This can either be a standard power outlet that is within reach or a socket with a dual pole switch
that completely disconnects power.
- The device may not be mounted in a completely closed construction. There must be enough ventilation and
space to monitor the machine at all times.

Temperature-related instructions:

- The device requires time for the heating element to warm up. For this reason, the machine can not be used 
directly after being switched on.
- The temperature settings of the smoke machine have been factory-optimised and can not be adjusted by 
the user.
- The smoke that comes out of this machine directly in front of the output nozzle is very hot. Keep animals, 
children, flammable objects and electronics away from the output nozzle of this smoke machine.
- When you are finished using the device, make sure it is switched off before removing the cable from the 
power outlet. The machine will still be hot after use and requires some time to cool down. Allow the smoke 
machine at least 20 minutes to cool down before transport.
- The smoke machine may produce small plumes of smoke after it has been switched off.

Ventilation and health-related instructions:

- Always ensure that there is sufficient ventilation in the room. There must be access to fresh air so the 
smoke can be removed quickly if necessary.
- Pay attention to the amount of smoke this machine produces. Only a small amount is required to make light

The information in this user manual is subject to change at any time without notice.

Version: 1.0

Date of creation and author's initials: 29-07-2017 RV

Revision date and author's initials: -

WARNING!

This device is equipped with a built-in heating element. The housing can become very hot during
use. Do not touch the housing of this machine while it is in use and never place your hand in 
front of the output nozzle. 

WARNING!

When a large quantity of fog is being produced in a poorly-ventilated room, some people may 
become light-headed or dizzy. If anyone develops these symptoms, it is advised to stop 
producing smoke immediately. Open a door or window to let in some fresh air and/or activate an 
indoor ventilation system. 

Summary of Contents for 9000-0033-5447


















Reviews: