0 4
A S S E M B L Y (see page 31)
F A U L T
C A U S E
R E M E D Y
⁄ Insufficient water
⁄ Supply pressure inadequate
⁄ Check water pressure (If a pump has been installed check
to see if the pump is working).
⁄ Regulator filter dirty
⁄ Clean filter in front of the mixer and on the MTC-thermo
cartridge
⁄ Shower filter seal dirty
⁄ Clean filter seal between shower and hose
⁄ Crossflow, hot water being forced into cold water pipe, or
vice versa, when mixer is closed
⁄ Backflow preventers dirty or leaking
⁄ Clean backflow preventers, exchange if necessary
⁄ Spout temperature does not correspond with temperature
set
⁄ Thermostat has not been adjusted
⁄ Adjust thermostat
⁄ Water pressure to low
⁄ Increase hot water temperature to 42 ºC to 65 ºC
⁄ Temperature regulation not possible
⁄ thermo cartridge calcified
⁄ Exchange thermo cartridge
⁄ Shower or spout dripping
⁄ Dirt or sedimentation on valve seat, shut-off unit damaged
⁄ Clean or exchange shut-off unit
⁄ Instantaneous heater didn’t work
⁄ Flow limiter in handshower isn’t removed
⁄ Remove flow limiter
⁄ Shower filter seal dirty
⁄ Clean filter seal between shower and hose
⁄ check valve hasn't moved back
⁄ Exchange check valves
C L E A N I N G (see page 40)
S P A R E P A R T S (see page 39)
F L O W D I A G R A M (see page 38)
Shower outlet
Tub outlet
D I M E N S I O N S (see page 38)
O P E R A T I O N (see page 35)
M A I N T E N A N C E (see page 36)
⁄ To guarantee the smooth running of the thermostat, it is necessary from
time to time to turn the thermostat from total hot to total cold.
⁄ The check valves must be checked regularly according to DIN EN 1717
in accordance with national or regional regulations (at least once a year).
A D J U S T M E N T (see page 34)
After the installation, the output temperature of the thermostat must be
checked. A correction is necessary if the temperature measured at the output
differs from the temperature set on the thermostat.
S A F E T Y F U N C T I O N (see page 34)
The desired maximum temperature for example max. 42º C can be pre-set
thanks to the safety function.
Do not use silicone containing acetic acid!
S Y M B O L D E S C R I P T I O N
S A F E T Y N O T E S
Gloves should be worn during installation to prevent crushing and cutting injuries.
Children as well as adults with physical, mental and⁄or sensoric impairments must
not use this product without proper supervision. Persons under the influence of
alcohol or drugs are prohibited from using this product.
The shower system may only be used for bathing, hygienic and body cleaning
purposes.
The hot and cold supplies must be of equal pressures.
I N S T A L L A T I O N I N S T R U C T I O N S
⁄ Prior to installation, inspect the product for transport damages. After it has been
installed, no transport or surface damage will be honoured.
⁄ The pipes and the fixture must be installed, flushed and tested as per the applicable
standards.
⁄ The plumbing codes applicable in the respective countries must be oberserved.
⁄ If the water connections are not stabil mounted, the fitting must be fixed with extra
screws (see page 31 Fig. A1 - A18, see page 36 Fig. A1 - A9). With this type of instal-
lation, take care not to puncture the water pipe! If the water connections are stabil
mounted, no extra screws are required (see page 32 Fig. B1 - B15, see page 37 Fig.
B1 - B12).
T H E R M O S T A T I C M I X E R I N C O N J U N C T I O N W I T H C O M -
B I N A T I O N B O I L E R S
If fitting a hand shower remove the water limiter from the shower.
T E C H N I C A L D A T A
Operating pressure:
max. 1 MPa
Recommended operating pressure:
0,1 - 0,5 MPa
Test pressure:
1,6 MPa
(1 MPa = 10 bar = 147 PSI)
Hot water temperature:
max. 70°C
Recommended hot water temp.:
65°C
Thermal disinfection:
max. 70°C ⁄ 4 min
Safety against backflow
The product is exclusively designed for drinking water!
EN
T E S T C E R T I F I C A T E (see page 39)
