manualshive.com logo in svg

Axon Synapse DEE28, Installation And Operation Manual, Page: 38 / 49

Share
Download
Axon Synapse DEE28 Installation And Operation Manual Download Page 38

 

38 

8  LED Indication

 

 

 

ERROR 

The error LED indicates an error if the internal logic of the DEE28 card 
is not configured correctly or has a hardware failure. 

 

 

INPUT 1 ~ INPUT 8  

These  LEDs  indicated  the  presence  of  a  valid  AES/EBU  signal  on  the 
inputs 1 till 8.  

 

 

REFERENCE 

This LED indicates the presence of a valid reference signal and that the 
DEE28 is locked to the master card. 

 

 

DATA ERROR 

This  led  indicates  different  types  of  errors  if  there  is  an  error  in  the 
Dolby encoding, or the audio carrier is falling away, or audio data is in 
the range of 0 dBFS and -1 dBFS. 

 

 

CONNECTION 

This  LED  illuminates  after  the  card  has  initialized.  The  LED  lights  for 
0.5 seconds every time a connection is made to the card. 

 

 

 

Note: 

When  LEDS  are  blinking  constantly,  the  card  is  still 

programming.  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for Synapse DEE28


















































Reviews:

No comments