manualshive.com logo in svg

Axon Synapse DEE28, Installation And Operation Manual, Page: 28 / 49

Share
Download
Axon Synapse DEE28 Installation And Operation Manual Download Page 28

 

28 

 

#RfMode 

RfMode

 has the same options as Line, but each option is 11 dB more 

sensitive to avoid overloading the RF input of a television. Possible are: 

None

, 

Film stnd

, 

Film light

, 

Music stnd

, 

Music light

 

and 

speech

. Default is 

None

. 

 

 

#D Srnd 

Dolby Surround

. Determines when a Dolby Digital decoding 

product also contains a Dolby Pro Logic decoder, whether the two-
channel encoded bistream contains a Dolby Surround (Lt/Rt) program 
that requires Pro Logic decoding. Decoders can use this flag to 
automatically switch on Pro-logic decoding as required.  

 

Not indic

, Not Indicated  

 

Not Srnd

, Not Dolby surround; the bitstream contains 

information that was not Dolby Surround encoded. 

 

Dolby Srnd

, Dolby Surround; the bitstream contains 

information that was Dolby Surround encoded. After Dolby Digital 
decoding, the bitstream is pro logic decoded. 

 

 

#Pref dwnmx 

Preferred Down mix. This parameter allows the user to select either Lt/Rt 
or the Lo/Ro downmix in a consumer decoder that has stereo outputs. 
Consumer receivers are able to override this selection, but this parameter 
provides the opportunity for a 5.1 channel soundtrack to play in 

Lo/Ro

 

mode without user intervention. This is especially useful on music 
material. 

NOT indicated

, 

Lt/Rt

 and 

Lo/Ro

 are the possible mix 

types. Default is 

Lt/Rt

. 

 

 

#Lt/RT C dwnmx 

Lr/Rt Center Mix Level. This setting indicates the level shift applied to 
the center channel when adding to the left and right outputs when 
downmixing to an Lt/rt output. Its operation is similar to the surround 
downmix level in the Universal metadata. 

+3dB

, 

+1.5dB

, 

0dB

, 

-

1.5dB

,

 -3.0dB

, 

-4.5dB

, 

-6.0dB

 and 

–999dB

. Default is -3.0dB. 

 

 

#Lt/RT S dwnmx 

LtRt Surround Mix level. This setting indicates the level shift applied to 
the surround channels when downmixing to an Lt/Rt output. Its operation 
is similar to the surround downmix level in the universal metadata.  

-

1.5dB

, 

-3.0dB

, 

-4.5dB

, 

-6.0dB

 and 

-999dB

. Default is –3dB. 

 

 

#Lo/Ro C dwnmx 

Lo/Ro Center mix level. This setting indicates the level shift applied to 
the center channel when adding to the left and right outputs when 
downmixing to a Lo/Ro output. When Extended BSI parameters are 
active, this parameter is used and the Center Mix Level parameter in the 
universal parameters is 

not

.

+3dB, +1.5dB, 0dB

, 

-1.5dB

, 

-

3.0dB

, 

-4.5dB

, -

6.0dB

 and 

-999dB

. Default is 

–3dB

.

  

 

 

 

#Lo/Ro S dwnmx 

Lo/Ro Surround Mix level.  This setting indicates the level shift applied 
to the surround channels when downmixing to a Lo/Ro output. When 
extended BSI parameters are active, this parameter is used, and the 

Summary of Contents for Synapse DEE28


















































Reviews:

No comments