Axon Synapse DEE28 Installation And Operation Manual Download Page 32 | Manualshive

Page: 32 / 49

Axon Synapse DEE28 Installation And Operation Manual Download Page 32

32

(MD) Bit_Depth

Indicates the value of the bit depth metadata parameter.

(MD) Dialogue_Lev

Indicates the value of the dialogue level metadata parameter.

(MD) Datarate

Indicates the value of the bitrate metadata parameter.

(MD) Bitstream

Indicates the value of the bitstream mode metadata parameter.

(MD) Channel_Mode

Indicates the value of the channel mode metadata parameter.

(MD) LFE

Indicates the value of the LFE channel metadata parameter.

(MD) Pref_Dwn_Mix

Indicates the value of the preferred downmix metadata parameter.

(MD) Center_mix_lvl

Indicates the value of the Center downmix level metadata parameter.

(MD) Surr_mix_lvl

Indicates the value of the surround downmix level metadata parameter.

(MD) Lt/Rt_center

Indicates the value of the Lt/Rt center downmix metadata parameter.

(MD) Lt/Rt_surr

Indicates the value of the Lt/Rt surround downmix metadata parameter.

(MD) Lo/Ro_center

Indicates the value of the Lo/Ro center downmix metadata parameter.

(MD) Lo/Ro_surr

Indicates the value of the Lo/Ro surround downmix metadata parameter.

(MD) DC_highpass

Indicates the value of the DC highpass filter metadata parameter.

(MD) BW_lowpass

Indicates the value of the bandwidth lowpass filter metadata parameter.

(MD) LFE_lowpass

Indicates the value of the LFE lowpass filter metadata parameter.

(MD) Surr_90

Indicates the value of the surround channel 90-degree phase shift filter
metadata parameter

«
...
30
31
32
33
34
...
»

Summary of Contents for Synapse DEE28


















































Reviews:

No comments