Axis M1045-LW Page 52 User Manual Download

Page: 52 / 62

AXIS M3006-V Network Camera

System Options

To avoid filling the share, it is recommended to remove recordings continuously. Under

Recording Settings

, select

Remove recordings

older than

and select the number of days or weeks.

To stop writing to the share and protect recordings from being removed, select

Lock

under

Recording Settings

Maintenance

The Axis product provides several maintenance functions. These are available under

System Options > Maintenance

Click

Restart

to perform a correct restart if the Axis product is not behaving as expected. This will not affect any of the current

settings.

Note

A restart clears all entries in the Server Report.

Click

Restore

to reset most settings to the factory default values. The following settings are not affected:

•

the boot protocol (DHCP or static)

•

the static IP address

•

the default router

•

the subnet mask

•

the system time

•

the IEEE 802.1X settings

•

uploaded applications are kept but must be restarted

Click

Default

to reset all settings, including the IP address, to the factory default values. This button should be used with caution. The

Axis product can also be reset to factory default using the control button, see

Reset to Factory Default Settings on page 53

To identify the product or test the Status LED, click

Flash LED

under

Identify

and specify the duration in seconds, minutes or hours.

This can be useful for identifying the product among other products installed in the same location.

For information about firmware upgrade, see

Upgrade the Firmware on page 55

Support

Support Overview

The

System Options > Support > Support Overview

page provides information on troubleshooting and contact information,

should you require technical assistance.

Summary of Contents for M1045-LW































































Search results

Summary of Contents for M1045-LW

Reviews:

Related manuals for M1045-LW

Brands by name

Popular brands

Axis M1045-LW, User Manual

Search results

Summary of Contents for M1045-LW

Reviews:

Related manuals for M1045-LW

Brands by name

Popular brands