Axis AXIS USB User Manual Download Page 13

Page: 13 / 61

Basic Installation

AXIS OfficeBasic USB User’s Manual

Section 3

Basic Installation

Connecting the Hardware

1. Make sure that your printer is switched off and that the print server’s

Power Adapter is disconnected.

2. Locate the

serial number

, found on the underside label of the print server,

and write it down. You will need this number to configure the print server.

Example

: S/N: 00408c181cf0

3. Connect the printer to the USB port using the USB cable.

4. Connect the print server to the network using a twisted pair category 5

cable, 10baseT or 100baseTX.

5. Switch on the printer and make sure it is ready for use.

6. Connect the Power Adapter to the print server. The power indicator will light

up. When the network indicator starts to flash, the print server is correctly
connected to the network.

7. Wait 1 minute. Press the test button on the print server once to print a test

page. The test page includes a list of the most important parameters.

Power Adapter
connector

Ethernet
connector

Network
indicator

Power

indicator

USB printer port (USB1)

Test button

Summary of Contents for AXIS USB






























































Search results

Summary of Contents for AXIS USB

Reviews:

Brands by name

Popular brands

Axis AXIS USB, User Manual

Search results

Summary of Contents for AXIS USB

Reviews:

Brands by name

Popular brands