manualshive.com logo in svg

Axis 2400/01, Administration Manual, Page: 78 / 87

Share
Download
Axis 2400/01 Administration Manual Download Page 78

 

78 

Es

pa

ño

l

 

Inventario de hardware

 

AXIS 2400/2401 Admin Manual

AXIS 2400/2401 Panel posterior

Nota:

La fuente de alimentación que se ofrece con su AXIS 2400/2401 depende del país. Por favor, 
compruebe que el tipo de fuente de alimentación que utiliza es correcta. Vea abajo.

Inventario de hardware

Compruebe los elementos que se ofrecen con la AXIS 2400/2401 teniendo en cuenta la lista siguiente:

Elemento

Título/Variantes

Referencias

Elemento

Título/Variantes

Referencias

Servidor de video

 

AXIS 2400

0092- 001- 02

PSU (PS-D)

Europa

14233

AXIS 2401 (NTSC)

0103-011-02

R.U.

14234

AXIS 2401 (PAL)

0103-001-02

Australia

14255

Cable de módem nulo

-

16954

EE.UU.

14253

Documento de garantía

-

18640

Japón

14254

Disco Media

AXIS Network 
Camera CD v2.0 
(o posteriores)

-

Este 
documento

AXIS 2400/2401 
Administration 
Manual v2.1

19097

Conector de serie RS-232

Dos conectores D-sub de 9 pins para conexiones en 
serie de tipo RS-232. Normalmente utilizadas para 
conectar dispositivos Pan/Tilt. COM1 está multi-
plexado con el puerto RS-485 a través del conector 
del bloque terminal. COM2 puede utilizarse para 
conectar el módulo de audio AXIS 2191.

Conector de fuente de 

alimentación

Un jack (PS-D) para conexión de la 
fuente de alimentación de AXIS 
2400/2401  El conector del bloque 
terminal le proporciona un punto de 
conexión auxiliar para la fuente AC 
o DC a la unidad.

Conector de red

La AXIS 2400/2401 soporta redes Ethernet de 10 Mbps y Fast 
Ethernet de 100 Mbps y se conecta a la red a través de un cable de 
par trenzado de categoría 5 (10baseT y 100baseTX) con conector 
estándar RJ45. La AXIS 2400/2401 detecta automáticamente la 
velocidad de la red y varía la velocidad de comunicación de datos 
en función de esto (entre 10 Mbps y 100 Mbps).

Bloque terminal I/O

Bloque terminal I/O El conector del bloque terminal I/O está situado entre 
los dos puertos de serie en el panel posterior y proporciona la interfaz física 
a una salida de clavija relé, cuatro entradas de imagen acopladas y una 
interfaz RS-485. Utilice este conector para transmitir datos por líneas de 
comunicación multiterminales, dispositivos RS-485 Pan Tilt y activación 
externa normalmente asociada con equipo CCTV. El conector puede usarse 
como un punto de conexión alternativo para fuente DC a la unidad. 

POWER 

PS-D

COM 1

COM 2

ETHERNET

10/100

1   2   3   4   5   6   7   8

9 10 11 12 13 14 15 16

Summary of Contents for 2400/01
























































































Reviews:

No comments