manualshive.com logo in svg

Axis 2400/01, Administration Manual, Page: 65 / 87

Share
Download
Axis 2400/01 Administration Manual Download Page 65

AXIS 2400/2401 Admin Manual

Werkseitige Standardeinstellungen

 

65 

Deut

sch

Werkseitige Standardeinstellungen

Unter bestimmten Umständen kann es erforderlich sein, die 

werkseitigen 

Standard

einstellungen

 

Ihres AXIS 2400/2401 wiederherzustellen. Klicken Sie dazu auf die 

entsprechende Schaltfläche in den 

Verwaltungsprogrammen

, 

oder

 drücken Sie die 

Kontroll-Taste

. Die Kontrolltaste ist in das Produktgehäuse eingelassen und sitzt beim 

AXIS 2400 zwischen dem VIDEO 3- und VIDEO 4-Anschluss. Beim AXIS 2401 sitzt sie 
links vom VIDEO OUT-Anschluss.

Befolgen Sie die Anweisungen, um die werkseitigen Standardeinstellungen mithilfe der 
Kontroll-Taste wiederherzustellen:

1.

Schalten Sie den

AXIS 2400/2401 

aus, indem Sie das Netzkabel ziehen.

2. Drücken Sie mit einem geeigneten spitzen Gegenstand die Kontroll-Taste und halten 

Sie sie gedrückt, während Sie das Netzkabel wieder einstecken.

3. Halten Sie die Kontroll-Taste gedrückt, bis die Statusanzeige 

gelb

 leuchtet (dies kann 

bis zu 15 Sekunden dauern). Lassen Sie die Kontroll-Taste los. Die Statusanzeige 

leuchtet nach max. 1 Minute 

grün

, und im AXIS 2400/2401 sind jetzt wieder die 

werkseitigen Standardeinstellungen geladen.

Hinweis:

Beim Wiederherstellen der ursprünglichen Standardeinstellungen werden alle Parameter, ink-
lusive IP-Adresse, zurückgesetzt.

Summary of Contents for 2400/01
























































































Reviews:

No comments