manualshive.com logo in svg

Axis 2400/01, Administration Manual, Page: 51 / 87

Share
Download
Axis 2400/01 Administration Manual Download Page 51

AXIS 2400/2401 Admin Manual

The RS-232 Interface

 

51 

Appendix F - The RS-232 Interface

The 

AXIS 2400/2401 has 

two 9-pin D-sub connectors, providing the physical interface for 

two RS-232 ports, used for connecting:

• accessory equipment; such as stand-alone Pan/Tilt devices for remote positioning of con-

nected video cameras 

• any standard modem for use in remote applications, as described on page 11
• the AXIS 2191Audio Module, as described on page 31.

As a complement to the information provided in

 Pan Tilt Settings,

 on page 26, this 

appendix describes how to install a standalone Pan/Tilt device to the AXIS 2400/2401 
Video Server.

Physical Connector

A diagram representative of both RS-232 connectors, complete with an accompanying pin 
assignment table, is shown below.

Notes:

The pinout is different for each supported serial port. 
Pin 4 on COM1 is connected to Pin 7 (RTS).
NC = Not connected

Pin

COM1 

Function

COM2

Function

1

NC

CD

2

- RXD

- RXD

3

- TXD

- TXD

4

DTR

DTR

5

GND

GND

6

DSR

DSR

7

RTS

RTS

8

NC

CTS

9

NC

RI

5

4

3

2

1

6

7

8

9

Summary of Contents for 2400/01
























































































Reviews:

No comments