DETAIL
OF AUDIO CHANGEOVER REMOTER
| DETAIL OF AUDIO CHANGEOVER REMOTER
h.
SIGNAL A
: It only corresponds to the Audio-Detector of input -A, this GPO goes to (1) when the source located
at the entrance -A is considered valid.
i.
SIGNAL B
:Only corresponds to the Audio-Detector of Input -B, this GPO goes to (1) when the source located
at input-B is considered invalid.
j.
SIGNAL AN OUT
: Corresponds to the Analog output, and the GPO goes to (1) when there is audio on the
Analog output.
k.
OFF
: GPO Off, not able to operate.
l.
ON
: GPO On, GPO continues to be enabled (1).
m.
GPIN 2 MIRROR
: Performs the step from (0) to (1) depending on what is received on GPIN (in this example the
GPIN 2).
n.
DTMF FUN1 START PULSE:
This command performs a pulse of 300ms on the door GPOut (1 - 300 ms
duration) whenever the corresponding DTMF signal FUNCTION -1 makes a transition from 0 to 1.
o.
DTMF FUN1 STOP PULSE
:
This command performs a pulse of 300ms on port GPOut (0 - 300ms duration)
whenever the consideration DTMF signal FUNCTION -1 performs a transition from 1 to 0.
p.
DTMF FUN2 START PULSE:
This command performs a pulse of 300ms on the door GPOut (1 - 300 ms
duration) whenever the corresponding DTMF signal FUNCTION -2 makes a transition from 0 to 1.
q.
DTMF FUN2 STOP PULSE
:
This command performs a pulse of 300ms on port GPOut (0 - 300ms duration)
whenever the consideration DTMF signal FUNCTION -2 performs a transition from 1 to 0.
r.
DTMF FUN3 START PULSE:
This command performs a pulse of 300ms on the door GPOut (1 - 300 ms
duration) whenever the corresponding DTMF signal FUNCTION -3 makes a transition from 0 to 1.
s.
DTMF FUN3 STOP PULSE
:
This command performs a pulse of 300ms on port GPOut (0 - 300ms duration)
whenever the consideration DTMF signal FUNCTION -3 performs a transition from 1 to 0.
t.
DTMF FUN4 START PULSE:
This command performs a pulse of 300ms on the door GPOut (1 - 300 ms
duration) whenever the corresponding DTMF signal FUNCTION -4 makes a transition from 0 to 1.
u.
DTMF FUN4 STOP PULSE
:
This command performs a pulse of 300ms on port GPOut (0 - 300ms duration)
whenever the consideration DTMF signal FUNCTION -4 performs a transition from 1 to 0.
The DTMF command
FUNx START PULSE
and the DTMF command
FUNx STOP PULSE
: This is extremely important
when one needs to command the remote automation systems, whether they be television or radio and/or the control and
command of transmitters via remote telemetry, and one needs to have a command pulse of duration of 300ms, rather
than a command stable, which then resets after "n" time as for
DTMF FUNx
Summary of Contents for GENIUS D
