Installing under UNIX/LINUX
164
AX3000 Models 80 and 85 - User's Manual
Each auxiliary port using the tty protocol (see Chapter 3.5.4) is identified by the name of the
AX3000 (from the
/etc/hosts
file) and a special keyword. For example:
axel1
aux1
/dev/ptyp12
/dev/ttyp12
axel1
aux2
/dev/ptyp13
/dev/ttyp13
axel2
parallel /dev/ptyp2
/dev/ttyp2
An auxiliary port controlled by the tty server is seen as a Unix/Linux local port (like a multi I/O
board).
Data can be sent to an auxiliary port by:
- Either a redirection to the ttyp (example: "cat file > /dev/ttyp12")
- Or declaring a local printer attached to the ttyp (/dev/ttyp12). This printer is used through the
lp command.
8.3.2 - The LPD Protocol
Set the auxiliary port as shown in Chapter 3.5.2.
Use the appropriate UNIX system management tool to add a remote printer. At least, two
parameters are requested:
- The name of the remote host: enter the AX3000's hostname (refer to
/etc/hosts
),
- The name of the printer: this is the
Printer Port Name
entered when the AX3000 was set up.
Run the
lp
command to use this printer.
Note
: some options of the
lp
command (number of copies, banner, etc) cannot be used, because
the AX3000 is not a UNIX server and has no hard disk on which to run a spooler.
8.3.3 - The rsh Command
The rsh command (or rcmd on SCO OpenServer) can be used to print a file.
The rsh parameters are:
- The hostname or the IP address of the device,
- A keyword which is the AX3000 auxiliary port name. This name has been set through the
AX3000 Set-Up (see Chapter 3.5.6).
To print a file, the rsh command reads data from 'standard input' (
stdin
) and sends this data to
one of the AX3000’s auxiliary ports. For example:
$ rsh axname parallel < file <CR>
In this example,
axname
is the name of the AX3000 (refer to
/etc/hosts
file) and
parallel
is
the Printer Port Name of the AX3000 auxiliary port.
8.3.4 - Using Transparent Mode
One of the auxiliary or logical ports should be selected as the default printer port which will be
controlled by escape sequences.
Select the
[Configuration]-[Terminal]-[Miscellaneous]
dialog and set the 'default printer port'.
This default port can only be used if no network service (lpd, tty, etc) is currently using it.
Summary of Contents for AX3000 80
