AW 781785-01 Manual Download Page 2

Page: 2 / 23

GETTING STARTED GUIDE

PXIe-5163

PXIe, 200 MHz, 1 GS/s, 14-bit PXI Oscilloscope

Note

Before you begin, install and configure your chassis and controller.

This document explains how to install, configure, and test the PXIe-5163. The PXIe-5163 is a
200 MHz, 1 GS/s oscilloscope.

Documentation for the PXIe-5163 is available from the

Start

menu by navigating to

NI-SCOPE Documentation

in the

National Instruments

folder.

Contents

PXIe-5163 SCB-19 Pinout..............................................................................................10
PXIe-5163 Mini-HDMI Breakout Cable to 6 BNC Pinout.............................................11

Configuring the PXIe-5163 in MAX...................................................................................... 12
PXIe-5163 Self-Calibration.................................................................................................... 12

Running Self-Calibration................................................................................................ 13

First Measurements................................................................................................................. 13

Making a Measurement with InstrumentStudio..............................................................13
Making a Measurement with LabVIEW.........................................................................14
PXIe-5163 Compensating Passive Probes...................................................................... 14

Programming the PXIe-5163.................................................................................................. 16

NI-SCOPE Examples......................................................................................................18

Troubleshooting...................................................................................................................... 19

Why Is the ACCESS LED Off When the Chassis Is On?...............................................19
What Should I Do if the PXIe-5163 Doesn't Appear in MAX?......................................19
What Should I Do if the PXIe-5163 Fails the Self-Test?................................................20

Where To Go Next.................................................................................................................. 21
Worldwide Support and Services............................................................................................ 21

Summary of Contents for 781785-01
























Search results

Summary of Contents for 781785-01

Reviews:

Related manuals for 781785-01

Brands by name

Popular brands

AW 781785-01, Manual

Search results

Summary of Contents for 781785-01

Reviews:

Related manuals for 781785-01

Brands by name

Popular brands