AVYCON AVC NBL21M-L1 Manual Download Page 41 | Manualshive

Page: 41 / 65

background image

If the captured license plate doesn’t meet the above requirement, you can
adjust the pan angle of the camera to correct it.

4.6 Network Configuration

4.6.1 TCP/IP

Go to Config



Network



TCP/IP interface as shown below. There are two ways for

network connection.

Use IP address (take IPv4 for example)-There are two options for IP setup: obtain
an IP address automatically by DHCP and use the following IP address. Please
choose one of the options as needed.

Test:

Test the effectiveness of the IP address by clicking this button.

Use PPPoE-Click the “PPPoE Config” tab to go to the interface as shown below.
Enable PPPoE and then enter the user name and password from your ISP.

Either method of network connection can be used. If PPPoE is used to connect
internet, the camera will get a dynamic WAN IP address. This IP address will change

«
...
39
40
41
42
43
...
»

Summary of Contents for AVC NBL21M-L1


































































Reviews:

No comments

Related manuals for AVC NBL21M-L1

Brand: Hama Pages: 60

Brand: jablotron Pages: 2

Brand: jablotron Pages: 17

Brand: Hitron Pages: 71

INFRAcontrol R 180

Brand: Kopp Pages: 2

Brand: Iget Pages: 2

Brand: OEM Optical Pages: 25

Brand: ZKTeco Pages: 55

Brand: Hanwha Vision Pages: 65

Brand: Alecto Pages: 76

Brand: A-MTK Pages: 17

Brand: Zavio Pages: 13

Brand: Europlex Pages: 15

Brand: Super Circuits Pages: 28

Brand: SOMFY Pages: 40

Brand: Braun Pages: 44

Brand: Xineron Pages: 12

Brand: Brickhouse Security Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands