AVYCON AVC NBL21M-L1 Manual Download Page 14 | Manualshive

Page: 14 / 65

background image

The following table is the instructions of the icons on the live view interface.

Icon

Description

Icon

Description

Original size

Zoom out

Fit correct scale

Zoom/Focus control

Auto (fill the window)

SD card recording indicator

Full screen

Sensor alarm indicator

Start/stop live view

Motion alarm indicator

Start/stop two-way

audio (only available

for the model with

audio input connector)

Color abnormal indicator

Enable/disable audio

Abnormal clarity indicator

Snapshot

Scene change indicator

Start/stop

local

recording

License plate detection

Zoom in

Those smart alarm indicators will flash only when the camera supports those
functions and the corresponding events are enabled.
In full screen mode, double click on the mouse to exit or press the ESC key on the
keyboard.
Click AZ control button to show AZ control panel. The descriptions of the control
panel are as follows:

Icon

Description

Icon

Description

Zoom -

Zoom +

Focus -

Focus +

One key focus (used when image is out of focus after manual

adjustment

«
...
12
13
14
15
16
...
»

Summary of Contents for AVC NBL21M-L1


































































Reviews:

No comments

Related manuals for AVC NBL21M-L1

Brand: Zivif Pages: 14

Brand: Samsung Pages: 11

Brand: Samsung Pages: 128

Brand: Samsung Pages: 1

Brand: 2gig Technologies Pages: 8

Brand: 2gig Technologies Pages: 2

Brand: CADDX Pages: 6

Brand: Eaton Pages: 12

Brand: Velleman Pages: 3

Brand: IDEM SAFETY SWITCHES Pages: 2

Brand: BSM Pages: 17

Brand: Intellinet Pages: 5

Brand: Speco Pages: 2

Brand: TPG Pages: 6

Brand: RED SHIELD Pages: 25

Brand: Uniden Pages: 66

Brand: LaView Pages: 26

Mainline CV-M13B10-ODI

Brand: Clare Controls Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands