manualshive.com logo in svg

Avocent Cyclades ACS 5000 SERIES, Command Reference Manual, Page: 96 / 152

Share
Download
Avocent Cyclades ACS 5000 SERIES Command Reference Manual Download Page 96

88

        Cyclades ACS 5000 Advanced Console Server Command Reference Guide

the parameter s1.data_buffering, though the value cannot be zero since a zero value turns off 
data buffering.

The conf.nfs_data_buffering parameter format is,

<server name or IP address>:<remote pathname>

For example, if data buffering is enabled for port 1, the data is stored in the file ttyS1.data in local 
directory /var/run/DB or in remote server indicated by conf.nfs_data_buffering.

Ramdisk

Data buffering files are created in the directory /var/run/DB. If the parameter s<nn>.alias is 
configured for the port <nn>, this name is used. For example, if the alias is called fremont_server, 
the data buffering file is named fremont_server.data. 

Linear vs. Circular buffering

For local data buffering, this parameter allows users to buffer data in either a circular or linear 
fashion. Circular format (cir) is a revolving buffer file that is overwritten whenever the limit of the 
buffer size (set by all.data_buffering) is reached. In linear format (lin), data transmission between 
the remote device and the serial port ceases once the 4k bytes Rx buffer in the kernel is reached. 
Then if a session is established to the serial port, the data in the buffer is shown 
(all.dont_show_DBmenu or sxx.dont_show_DBmenu must be 2), cleared and data transmission is 
resumed. Linear buffering is impossible if flow control is set to none. Default is cir.

To configure data buffering:

1.

Execute the following command to configure data buffering. Refer to Table 5.12 for the 
configuration parameters.

cli> 

config physicalports all databuffering [parameter] <value>

2.

Activate and save your configuration.

Table 5.12: Data Buffering Configuration Parameters 

Parameter

Value

Description

bufferonlynosession

no|yes

Buffer only when connected to the serial port.

buffersyslogonlynose
ssion

no|yes

Only syslog is buffered.

desttype

local | remote

Define the data buffering location.

filesize 

<file size in bytes>

Defines the maximum size of the data buffer file. This 
parameter must be greater than zero otherwise all 
parameters relating to data buffering are disregarded.

mode

cir | lin

Choose between circular or linear data buffering.

nfspath

<pathname>

Define the NFS path.

Summary of Contents for Cyclades ACS 5000 SERIES

























































































































































Reviews:

No comments