manualshive.com logo in svg

Avocent Cyclades ACS 5000 SERIES, Command Reference Manual

Share
Download
Avocent Cyclades ACS 5000 SERIES Command Reference Manual Download Page 34

26

        Cyclades ACS 5000 Advanced Console Server Command Reference Guide

UDP extensions

These extensions are loaded if the protocol udp is specified or -m udp is specified. It provides the 
following options.

ICMP extension

This extension is loaded if the protocol icmp is specified or -m icmp is specified. It provides the 
following option.

NOTE: 

For IPv6 configurations, the icmpv6 protocol is used.

[!] - - syn 

Only match TCP packets with the SYN bit set and the ACK and FIN bits 
cleared. Such packets are used to request TCP connection initiation; for 
example, blocking such packets coming in an interface prevents 
incoming TCP connections, but outgoing TCP connections are 
unaffected. It is equivalent to - -tcp-flags SYN,RST,ACK SYN. 
If the ! flag precedes the - -syn, the sense of the option is inverted.

- - tcp-option [!] number

Match if TCP option is set. 

Table 2.12: UDP Extensions 

UDP extension

Description

- - source-port [!] [port[:port]] 

Source port or port range specification. See the description of the - -
source-port option of the TCP extension for details. 

- - destination-port [!] [port[:port]] 

Destination port or port range specification. See the description of the - -
destination-port option of the TCP extension for details.

Table 2.13: ICMP Extensions 

ICMP extension

Description

- - icmp-type [!] typename

This allows specification of the ICMP type, which may be a numeric ICMP 
type, or one of the ICMP type names shown by the command 
iptables p icmp -h

Table 2.11: TCP Extensions (Continued)

TCP extension

Description

Summary of Contents for Cyclades ACS 5000 SERIES

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands