manualshive.com logo in svg

Avocent Cyclades ACS 5000 SERIES, Command Reference Manual, Page: 100 / 152

Share
Download
Avocent Cyclades ACS 5000 SERIES Command Reference Manual Download Page 100

92

        Cyclades ACS 5000 Advanced Console Server Command Reference Guide

To set up which servers the users may access:

1.

Enter the following command to set up a menu, which is prompted when you connect from a 
dumb terminal. Refer to Table 5.13 for configuration parameters.

cli> 

config applications terminalmenu add [parameter] <value>

2.

Activate and save your configuration.

NOTE: 

You may open an SSH connection to the desired server. To do so, substitute telnet host_ip with ssh -l 

username host_ip.

Terminal Appearance

You may change the banner appearance when a connection is made to a server. The banner 
appearance may be port-specific or a unified banner for all ports. 

To configure the terminal appearance:

1.

Enter the following command to configure a banner for one or multiple serial ports. 

cli> 

config physicalports [all|range] other banner "<login banner>"

NOTE: 

A banner string with spaces must be enclosed by double quotes "<string1 string2>".

2.

Activate and save your configuration.

Table 5.13: Terminal Profile Menu Configuration Parameters 

Parameter

Value

Description

menutitle

<string>

Type a description for the menu title bar.

actionname

<action name>

Enter n identification for the command. For example, 
server name.

command

<string>

Enter a command such as telnet host_ip.

Summary of Contents for Cyclades ACS 5000 SERIES

























































































































































Reviews:

No comments