manualshive.com logo in svg

AvL Technologies AAQ CIP, Setup & Operation Manual

Share
Download
AvL Technologies AAQ CIP Setup & Operation Manual Download Page 36

 

AAQ Controller Interface Panel (CIP)

 

 

 

 

 

35 

 

 

Label 

Description 

IPv4 Address: 

The address devices on the LAN will use to communicate to the 
router.  The address devices on the LAN will use as a gateway. 

Subnet: 

Subnet mask the router will use to communicate to devices 
on the LAN. 

DHCP LAN Server 
Enabled: 

Choice to enable the DHCP server on the LAN. 

DHCP Pool Beginning: 

The Start of the DHCP pool that the router will dispense to 

DHCP clients. 

DHCP Pool Ending: 

The End of the DHCP pool that the router will dispense to 

DHCP clients. 

NAT Rules Enabled: 

Choice to enable NAT rules that allow communication from 
the WAN network and passes it to the controller and remote 

power cycle device. 

 

NAT rules perform the task of mapping the controller to all requests and responses coming from the ‘Controller WAN 
IP’ to the AAQ Controller’s service IP (192.168.129.51).  This allows the control of the controller from a user on the 
WAN network.  All traffic destined for the ‘Controller WAN IP’ will be forwarded to the controller. 

 

AAQ Controller

CIP

IP: 192.168.129.51
SN: 255.255.255.0

IP: 192.168.129.1
SN: 255.255.255.0

IP: Controller WAN IP
SN: Controller WAN SN

IP: Power Cycle WAN IP
SN: Power Cycle WAN SN

Router

Remote Power Cycle

LAN

WAN

 

 

Figure 58 - NAT Mapping 

5.5.2.

 

Customer Network Setup (WAN) 

The WAN should include all equipment that the controller needs to communicate with gateway or firewall 
protection.  All modem router combination devices must be on this network.  The WAN is commonly referred to as 
the customer network and does not usually contain AAQ devices.  The router can be configured to have the 
following: 

 

 
 
 
 
 
 

Summary of Contents for AAQ CIP










































Reviews:

No comments

Brands by name

Popular brands

Load more brands